Oriental motor CSK Series Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 48

Oriental motor CSK Series Скачать руководство пользователя страница 8

I / O power supply connector ( CN1 SIGNAL) 24

Connected to I / O signals and a 24 VDC or 36 VDC power supply.

Motor connector ( CN2 MOTOR) 24

Connected to motor leads.

Power supply input indicator LED ( POWER )

Remains lit while current is supplied (green).

Function-setting switches

These switches are used to set driver functions.

●

Automatic current-cutback function switch (A.C.D.)

30

This switch enables or disables the automatic current-cutback function.
The switch is factory-set to [ ON : enable automatic current-cutback].

●

Step angle switch ( F/ H)

30

This switch sets the motor’s step angle (full step/half step).
The switch is factory-set to [ON (F): full step ].

●

Pulse input mode switch (1P/ 2P)

31

Set to 2-pulse input mode or 1-pulse input mode according to the
pulse output mode of the positioning controller.
The switch is factory-set to [OFF (2P) : 2-pulse input mode].

●

Power supply voltage switch (24/ 36 V )

31

Set to 24 V or 36 V, according to the driver’s power supply voltage.
The switch is factory-set to [ON (24 V)].

Potentiometer for adjusting the motor operating current (RUN VR) 33

This potentiometer sets the operating current of the motor.
If there is sufficient torque, the current setting can be reduced to suppress
increases in motor/driver temperatures.
The potentiometer is factory-set to [ the rated current ].

Potentiometer for adjusting the motor standstill current (STOP VR) 33

This potentiometer sets the current when the motor is at a standstill (in the
current-cutback state).
The potentiometer is factory-set to [40 percent of the rated current ].

Positive check terminal for motor operating current (C.C.

+

) 32

This terminal is used to check the motor operating current.

Negative check terminal for motor operating current (C.C. - ) 32

This terminal is used to check the motor operating current.

8

■

Names and functions of driver parts

This section covers the names and functions of the driver’s respective parts.
See the reference page indicated for details on each part.

●

CSD2109-P, CSD2112-P, CSD2120-P

1 2 3 4

OF

F

VEXTA

C.C.+

C.C.-

ACD

F/H

1P/2P

24/36V

RUN

VR

STOP

VR

P0W

CN2

MOTOR

CN1

SIG

NA

L

Mounting holes

2

1

5

3

8

6

7

4

1

5

6

7

8

2

3

4

«
...
6
7
8
9
10
...
»

Содержание CSK Series

















































Отзывы:

Нет отзывов