Omron TJ1-MC04 Скачать руководство пользователя страница 108 | Manualshive

Страница: 108 / 312

Omron TJ1-MC04 Скачать руководство пользователя страница 108

BASIC commands

PROGRAMMING MANUAL

108

Revi

si

on 3.0

3.2.173 MERGE

/i

Description

Note: This command has two forms, depending upon the function required:
Master and Station Functions.
All

MECHATROLINK

functions return

TRUE

(-1) if the command was suc-

cessful or

FALSE

(0) if the command failed.

The functions are separated out into 2 types,

MASTER

functions that work on

a unit, and

STATION

functions that work on a specific

station_address

of a

given unit.
All functions that retrieve a value store it in the

VR

variable indicated in the

last parameter. If this parameter has the value -1 then the value is printed to
the command line port.
Notes:
•

If a MECHATROLINK-II command fails then the MECHATROLINK-II sta-
tion will go into warning/alarm state. All subsequent commands will then
return this warning/alarm state, even if the command is question is per-
formed correctly.

•

The warning/alarm state can only be cleared by the

ALM_CLR

com-

mand.

•

There is no

ALM_CLR

subcommand, so in order to send the

ALM_CLR

you must enter commissioning mode.

Arguments

N/A

Example

No example.

See also

N/A

Type

Axis parameter

Syntax

MERGE

Description

The

MERGE

parameter is a software switch that can be used to enable or

disable the merging of consecutive moves. With

MERGE

is on and the next

move already in the next move buffer (

NTYPE

), the axis will not ramp down to

0 speed but will load up the following move enabling a seamless merge. The
default setting of

MERGE

is off.

It is up to the programmer to ensure that merging is sensible. For example,
merging a forward move with a reverse move will cause an attempted instan-
taneous change of direction.

MERGE

will only function if the following are all true:

1.

Only the speed profiled moves

MOVE

,

MOVEABS

,

MOVECIRC

,

MHELICAL

,

REVERSE

,

FORWARD

and

MOVEMODIFY

can be merged

with each other. They cannot be merged with linked moves

CONNECT

,

MOVELINK

and

CAMBOX

.

2.

There is a move in the next move buffer (

NTYPE

).

3.

The axis group does not change for multi-axis moves.

When merging multi-axis moves, only the base axis

MERGE

axis parameter

needs to be set.
Note: If the moves are short, a high deceleration rate must be set to avoid the
TJ1-MC__ decelerating in anticipation of the end of the buffered move.

Arguments

N/A

Example

MERGE = OFF ' Decelerate at the end of each move
MERGE = ON ' Moves will be merged if possible

See also

AXIS

.

I52E-EN-03.book Seite 108 Freitag, 29. Juni 2007 11:55 11

«
...
106
107
108
109
110
...
»

Содержание TJ1-MC04

























































































































































































































































































































Отзывы:

Нет отзывов