manualshive.com logo in svg

Omron E5CC-T, Руководство по связи

Поделиться
Скачать
Omron E5CC-T Скачать руководство пользователя страница 43

2 - 19

2   CompoWay/F Communications Procedures

E5

C-T Digital Temperature Controllers Programmable Type Communications Manual (H186)

2-3  Detailed D

escription 

of the Ser

v

ices

2

2-3-8  Oper

at

ion C

ommand

A parameter error will occur if 40% AT is specified during heating and cooling control or floating

position-proportional control.

Note: If the same type of AT execution is specified during AT execution (e.g., if 100% AT is specified during

100% AT execution), the AT will not be restarted and the operation will end in normal completion with
no processing.

•

Write Mode 

Set either the backup mode or RAM write mode with the related information setting. The setting

can be accepted in both setup area 0 and setup area 1. 

The number of non-volatile memory write operations is limited. Therefore, use RAM write mode

when frequently overwriting data.

•

When the mode is switched from RAM write mode to backup mode, the parameters in the

operation, program setting, adjustment, and PID setting levels (excluding read-only

parameters) are written to non-volatile memory.

•

The RAM write mode is enabled only when the Communications Writing parameter is set to

“ON” (enabled). 

Consequently, when the Communications Writing parameter setting is changed to "OFF"

(disabled), the parameters in the operation/adjustment levels (excluding read-only

parameters) are written to non-volatile memory even if the mode is set to RAM write mode.

•

Save RAM Data 

This command writes the parameters in the operation, program setting, adjustment, and PID

setting levels (excluding read-only parameters) to non-volatile memory. The setting can be

accepted in both setup area 0 and setup area 1.

•

Software Reset

Restarts processing from the point when power is turned ON. The setting can be accepted in both

setup area 0 and setup area 1. 

•

Move to Setup Area 1 

This command moves to “setup area 1” and can be accepted at both setup areas 0 and 1. If the

“initial setting/communications protect” is set to “2,” an “operation error” will be generated, and the

move to setup area 1 will be prohibited.

When this move is carried out from setup area 0, the display indicates the Input Type parameter in

the “initial setting level.” When this operation command is executed in setup area 1, the display will

not change.

•

Move to Protect Level

This command moves to the "protect level" and can be accepted only in setup area 0. When this

command is issued in setup area 1, an "operation error" will be generated, and the move to the

protect level will be prohibited.

•

Moving to Protect Level in Manual Mode

When this operation command is issued in manual mode, an “operation error” will be

generated, and the move to the protect level will be prohibited.

Write mode

Description

Backup mode

The data is written to non-volatile memory when the parameters in the 
operation, program setting, adjustment, and PID setting levels (excluding 
read-only parameters) are written by communications.

RAM write mode

The data is not written to non-volatile memory when the parameters in the 
operation, program setting, adjustment, and PID setting levels (excluding 
read-only parameters) are written by communications.

Содержание E5CC-T



























































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды