Omron E5CC-T Скачать руководство пользователя страница 175

Страница: 175 / 186

7 - 7

7 Component Communications



C-T Digital Temperature Controllers Programmable Type Communications Manual (H186)

7-3 T

rou
b

lesho

ting

7-3

Troubleshooting

Possible problems that can occur with component communications and corrective actions are given in

the following table.

Note: For information on other problems, refer to

A-2 Troubleshooting

Status

Cause and corrective action

Page

The set point or RUN/RESET status
will not change for a slave (i.e., a
Controller with a communications
unit number other than 0).

The wiring to the slave is not correct.

7-3

The communications settings for the slave are not
correct.

•

The Protocol Setting parameter is not set to

cmp

•

The Communications Unit No. parameter is set to
the same value as another slave.

•

The setting of the Communications Baud Rate
parameter is not the same as the other slaves.

•

The Highest Communications Unit No. parameter
is not set to the highest communications unit
number that is actually set.

•

The Communications Writing parameter is set to
OFF.

7-4

◆

When the RUN/RESET Does Not Change

RUN/RESET is assigned to an event input for the
slave.

7-6

◆

When the Set Point Does Not Change

The set point from the master or the results of set
point calculations exceeds the set point limiter of the
slave.

7-5
7-6

The set points or the RUN/RESET
status will not change for any of the
slaves.

The wiring to the master (i.e., the Controller with
communications unit number 0) is not correct.

7-3

The communications settings in the master are not
correct.

•

The Protocol Setting parameter is not set to

cmp

•

The Communications Unit No. parameter is not set
to 0.

•

The Communications Baud Rate parameter is not
set to the same value as the slaves.

•

The Highest Communications Unit No. parameter
is not set to the highest communications unit
number that is actually set.

7-4

The set point is not calculated.

•

The SP Slope or SP Offset parameter is not set
correctly.

•

The set point was changed at the master when the
slave was stopped (setting area 1).

7-5

It is sometimes not possible to
change the set points or
RUN/RESET status.

There may be noise interference. Connect
terminating resistance to both ends of the
communications line.

7-3

Содержание E5CC-T



























































































































































































Результаты поиска

Содержание E5CC-T

Отзывы:

Бренды по названию

Популярные бренды

Omron E5CC-T, Руководство по связи

Результаты поиска

Содержание E5CC-T

Отзывы:

Бренды по названию

Популярные бренды