Omron E5CC-T Скачать руководство пользователя страница 10

Страница: 10 / 186

Precautions for Safe Use



C-T Digital Temperature Controllers Programmable Type Communications Manual (H186)

•

Design the system (e.g., control panel) considering the 2 seconds of delay in setting the Digital

Controller’s output after the power supply is turned ON.

•

The output will turn OFF when you move to the initial setting level. Take this into consideration when

performing control.

•

The number of non-volatile memory write operations is limited. Therefore, use RAM write mode when

frequently overwriting data, e.g., through communications.

•

Use suitable tools when taking the Digital Controller apart for disposal. Sharp parts inside the Digital

Controller may cause injury.

•

Do not connect cables to both the front-panel Setup Tool port and the top-panel Setup Tool port at the

same time. Damage or malfunction may occur.

•

Do not exceed the communications distance that is given in the specifications and use the specified

communications cable. Refer to the

C-T Digital Temperature Controllers User’s Manual

(Cat. No.

H185) for the communications distance and cable specifications.

•

Do not turn the power supply to the Digital Controller ON or OFF while the USB-Serial Conversion

Cable is connected. The Digital Controller may malfunction.

•

Do not bend the communications cables past their natural bending radius. Do not pull on the

communications cables.

Содержание E5CC-T



























































































































































































Результаты поиска

Содержание E5CC-T

Отзывы:

Бренды по названию

Популярные бренды

Omron E5CC-T, Руководство по связи

Результаты поиска

Содержание E5CC-T

Отзывы:

Бренды по названию

Популярные бренды