Oki C710, Руководство по обслуживанию

Страница: 93 / 223

43856301TH Rev.3
92 /
Oki Data CONFIDENTIAL
5. Maintenance Menu
5.1 System maintenance menu (for maintenance engineer)
While pressing the MENU+ and MENU- keys, turn on the power to enter the maintenance menu.
The menu indications are shown in English only regardless of the destination of the printer.
Note! The system maintenance menu is internally use only, and should not be
disclosed to end user because destination and other parameters can be
modified using this menu.
Table 5-1 Maintenance menu function table
Category Item (1st Line)
Value
(2nd Line)
DF Function
System
Mainte-
nance
Enter Password ******
******
000
000
Enter the password to enter the system
maintenance menu.
Default value is "000000".
A password can be entered in the range of 6- to
12-digit alphanumeric.
For more details, refer to the "Password" sheet.
OKIUSER OKIUSER ODA
OEL
APS
JP1
JPOEM1
OEMA
OEML
* Set the destination.
JPOEM1 : Japanese OEM
OEMA : Overseas OEM outside Japan
of A4 size default
OEMA : Overseas OEM outside Japan
of the Letter size default
When the printer exits the menu, the printer
reboots automatically.
Mainte-
nance
Menu
[Display condition]
Encrypted hard disk function is disabled.
Format HDD Execute - Initializes the hard disk. When this menu item is
executed, the system exits the menu and starts
initializing the hard disk.
[Display condition]
HDD is installed. ("Boot Menu" - "Storage Setup"
= "Enable HDD" is set to "YES".)
Format Flash
ROM
Execute - Initializes the flash ROM.
When this menu item is executed, the system
exits the menu and starts formatting the flash
memory device that is installed resident (on-
board).
* Use of this menu item is prohibited.
Reset
EEPROM
Execute - Returns the EEPROM contents to the setup by
the manufacturer when shipped from the factory
(factory default profile) value. Upon completion
of the setting change, the system reboots
automatically.
* Some specific items are not initialized.
Category Item (1st Line)
Value
(2nd Line)
DF Function
Mainte-
nance Print
Menu
Maintenance
Print Menu Enable
Disable
* Selects whether or not to display "Print
Information" - "ID Check Pattern" and "Engine
Status".
When this menu item is set to "Disable", the
function menu "Print Information" - ID Check
Pattern" and "Engine Status" are not displayed
all the time.
When exiting this menu upon completion of
setting change, the printer reboots automatically.
Fuse Keep
Mode Fuse Keep
Mode Execute - When the ENTER key is pressed, the command
is issued from CU to PU to set the system in ON
LINE.
Replace the consumable part with the new part
while the power is turned on. (In this case, fuse
of the new consumable part is not cut, and the
operational counts are reset so that the count
value of old consumable part is not added.)
The check mode is terminated when the power
is turned off. The check mode is disabled when
the power is turned on next time.
Personality IBM 5577 Enable
Disable *
Changes the default of Support PDL per brand.
PDL which is "Disable" in this menu is not
displayed at "Print Setup" - "Personality" of
Function menu. INVALID DATA shows up and
received data is abandoned when print data of
PDL which is "Disable" is received.
IBM PPR III XL Enable
Disable
*
EPSON FX Enable
Disable
*
HP-GL/2 Enable
Disable *
Change
Password - Changes the password.
When the ENTER switch is pressed after
entering in this menu, the messages "NEW
PASSWORD" and "VERIFY PASSWORD"
are displayed enabling user to enter a new
password.
New Password ******
****** - Sets the new password to enter the
maintenance menu.
A password can be entered in the range of 6- to
12-digit alphanumeric.
Verify
Password ******
****** - Prompting user to verify the new password that
has been set by "NEWPASSWORD", to enter
the system maintenance menu.
A password can be entered in the range of 6- to
12-digit alphanumeric.
Diagnostic
Mode - Enters the self-diagnostic mode.