Oki C710, Руководство по обслуживанию

Страница: 141 / 223

43856301TH Rev.3
140 /
Oki Data CONFIDENTIAL
7. Troubleshooting and repair procedure
Display on operator panel
ON
LINE
lamp
Inspection
lamp
Contents Code nnn
Open the rear cover.
%ERRCODE%: Paper jam Off Blink Indicates that jam has occurred in
the vicinity of Duplex unit.
Error 370: Duplex Reversal
Error 371: Duplex Input
Error 373: Duplex Multifeed
Error
370
371
373
Open the front cover.
%ERRCODE%: Paper jam Off Blink Indicates that jam has occurred in
the vicinity of Duplex unit.
Error 372:Duplex misfeed
Error
372
Install the Duplex unit.
%ERRCODE%: Duplex
unit is not installed.
Off Blink Indicates that the Duplex unit is
removed.
If this error is detected, printing is
stopped.
Error
360
Replace the drum.
%ERRCODE%: The
%COLOR% drum has
reached end of life.
Off Blink Informs the image drum has reached
end of line (alarm).
When the cover is opened/closed, it
changes to the warning status.
Error 350: Y
Error 351: M
Error 352: C
Error 353: K
Error
350
351
352
353
Replace the drum.
%ERRCODE%: The
%COLOR% drum has
reached end of life.
Off Blink Informs the image drum has reached
end of line (alarm).
It is displayed until the image drum is
replaced.
Error 560: Y
Error 561: M
Error 562: C
Error 563: K
Error
560
561
562
563
Replace the fuser.
%ERRCODE%: The fuser
has reached end of life.
Off Blink Informs the image drum has reached
end of line. This error is issued when
the counter detects that the fuser has
reached end of life. Print is stopped.
When the cover is opened/closed, it
changes to the warning status.
Error
354
Replace the belt.
%ERRCODE%: The belt
has reached end of life.
Off Blink Informs that the transfer has reached
end of line. This error is issued when
the counter detects that the belt has
reached end of life. Print is stopped.
When the cover is opened/closed, it
changes to the warning status.
Error
355
Display on operator panel
ON
LINE
lamp
Inspection
lamp
Contents Code nnn
Re-set the fuser.
%ERRCODE%: Fuser
error
Off Blink Indicates that an error is issued in the
release position sensor of the fuser.
The printer recovers from this error if
the release position sensor has read
out the data after the cover is closed.
If the printer still cannot recover from
this error, replacement of the fuser is
required.
Error
348
Replace the belt.
%ERRCODE%: The belt
has reached end of life.
Off Blink Indicates that the waster toner is full.
It changes to the warning status after
the cover is opened and closed only
once. This error is issued again after
500 copies are printed.
Error
356
Check the toner cartridge.
%ERRCODE%:
%COLOR%.
The lock lever position is
incorrect.
Off Blink Indicates that the lever of the toner
cartridge is left unlocked.
Error 544: Y
Error 545: M
Error 546: C
Error 547: K
Error
544
545
546
547
Re-set the drum.
%ERRCODE%
:%COLOR%. Drum error
Off Blink Indicates that the image drum is not
installed normally.
Error 340: Y
Error 341: M
Error 342: C
Error 343: K
Error
340
341
342
343
Re-set the fuser.
%ERRCODE%
: Fuser error
Off Blink Indicates that the fuser is not
installed normally.
(This error can occur when the
printer temperature is below 0 degree
C. Turn on the power again after the
printer temperature has increased.)
Error
320
Re-set the belt.
%ERRCODE%: Belt error Off Blink Indicates that the belt is not installed
normally.
Error
330
Turn off the power and
wait for a while.
%ERRCODE%:MOTOR.
OVERHEAT
Off Blink Indicates the overheating of the ID
motor.
Error
321
Close the cover.
%ERRCODE%: Cover is
open.
Off Blink Indicates that the cover is open.
Error 310: Top cover
Error 311: Front cover
Error
310
311