Ochsner AIR 7 страница 37 Скачать руководство пользователя

Страница: 37 / 100

INSTALLATION | Appliance installation

982000-AIR-M2-M4-EN03.1 | www.ochsner.com 37

11_02_200_504_01_001

7
6
5
4

1 Fan fault message (TK1/TK2)

2 Fan power supply (L/N/PE)

3 Stepper motor of expansion valve A (1/2/3/4)

4 Suction gas sensor S2

5 Defrost sensor TQE (OTE pin 49/GND)

6 Defrost sensor TQA (OTE pin 50/GND)

7 Fan speed (0-10 VDC/GND)

8 Earth rail

10.5 Connecting heat source system

WARNING: Burns

Work on the refrigerant circuit may be carried out

only by an authorised and suitably qualified con

tractor. Refrigerant can cause burns to the skin.

When handling refrigerant, wear appropriate

gloves and protective glasses.

The following activities on air/water heat pumps must be

carried out by OCHSNER Customer Service or by a cus-

tomer service partner authorised by OCHSNER.

►

Connecting the previously laid refrigerant lines.

►

Conducting leakage tests on the refrigerant lines.

►

Emptying the refrigerant lines.

►

Insulating the refrigerant lines around the connection

points on the indoor and outdoor units.

►

Filling the system with the correct refrigerant accord-

ing to OCHSNER guidelines.

Information

The system installer must ensure that noise insu-

lating pipe fixings for the refrigerant lines and the

seals on the wall outlets are correctly fitted.

10.5.1 Connecting the refrigerant lines

Material damage

Incorrect or premature opening of the pipe connec-

tions and cutting of the refrigerant lines can allow

dirt and moisture to enter the refrigerant circuit.

Do not open the connections on the indoor

or outdoor units until just before installing the

refrigerant lines.

Cut the refrigerant lines with a suitable pipe

cutter.

Prevent swarf from contaminating the pipe

connections and refrigerant lines.

Flush the refrigerant lines fully with nitrogen.

The refrigerant circuits on both the outdoor and indoor

units are filled with nitrogen at the factory.

Please note the

following when installing the refrigerant lines:

Use the largest possible pipe bends to avoid high

pressure losses.

Use suitable sound-insulating pipe fixings to secure

the refrigerant lines.

Do not install the pipe fixings in the vicinity of bends

in the pipes.

Ensure that no strain can be exerted on soldered

joints.

Содержание AIR 7





































































































Результаты поиска

Содержание AIR 7

Отзывы:

Похожие инструкции для AIR 7

Бренды по названию

Популярные бренды

Ochsner AIR 7, Руководство по эксплуатации и установке

Результаты поиска

Содержание AIR 7

Отзывы:

Похожие инструкции для AIR 7

Бренды по названию

Популярные бренды