Ochsner AIR 7 страница 7 Скачать руководство пользователя

Страница: 7 / 100

OPERATION | Appliance description

982000-AIR-M2-M4-EN03.1 | www.ochsner.com 7

Compressor

The fully hermetically sealed compressor is designed for

high efficiency heat pump applications.

A suitable starting

current limiter for the compressor is installed in the indoor

unit.

Electric booster heater

The appliance is fitted with an electric booster heater

(immersion heater). At low outdoor temperatures, the ap-

pliance operates in bivalent-parallel mode. The appliance

can also be combined with an additional heat generator.

Condenser

The condenser takes the form of a plate heat exchanger,

which is built of stainless steel and insulated on all sides

against condensation and heat loss.

3.2.2 Outdoor unit

The outdoor unit is intended to be installed outside. The

outdoor unit is designed as a horizontal split evaporator.

The indoor unit is connected to the outdoor unit with refrig-

erant lines, along with electrical control and power supply

cables.

Evaporator

The evaporator is a part of the outdoor unit and consists

of copper pipes in a set of aluminium fins.

Information

With an air/water heat pump, frost may form on

the evaporator fins of the outdoor unit, depending

on the air temperature (below approx. +7°C), air

humidity and the operating point. The evaporator

fins are automatically de-iced again in the cyclical

defrosting mode of the heat pump.

Fan

The outdoor air is blown across the evaporator by a quiet

fan.

3.2.3 Heat pump control unit

The OCHSNER heat pump controller includes devices

for controlling heat pump heating systems with a cooling

function as well as DHW heating. In its standard version,

the heat pump control unit consists of the OTE controller

and the master controller, both of which are installed in

the indoor unit.

The OTE controller can control the following system circuits

and heat generators:

►

1x direct circuit (heating and/or cooling)

►

1x mixed circuit (heating and/or cooling)

►

1x directly heated DHW cylinder (with electric booster

heater)

►

1x heat pump (heating and cooling)

►

1x additional heat generator (electric booster heater

or enable contact for external heat generator)

3.3 Name plate

Two name plates are attached to the indoor unit to identify

your heat pump. In addition, a label with the serial number

is attached to the right-hand casing panel of the appliance.

11_02_200_214_01_004

1 Name plate (back of indoor unit and front of control

box)

2 Serial number (right-hand casing panel)

Содержание AIR 7





































































































Результаты поиска

Содержание AIR 7

Отзывы:

Похожие инструкции для AIR 7

Бренды по названию

Популярные бренды

Ochsner AIR 7, Руководство по эксплуатации и установке

Результаты поиска

Содержание AIR 7

Отзывы:

Похожие инструкции для AIR 7

Бренды по названию

Популярные бренды