Ochsner AIR 7 страница 36 Скачать руководство пользователя

Страница: 36 / 100

INSTALLATION | Appliance installation

www.ochsner.com | 982000-AIR-M2-M4-EN03.1

Information

For the cables inside the control box on the indoor

unit, use the cable strain reliefs provided.

Material damage

An external source of voltage at the sensor termi-

nals can destroy the OTE controller.

Ensure that no 230 VAC or 400 VAC cables

are touching the sensor terminals on the OTE

controller.

Connect the power supply cable for the control circuit

(X3).

Connect the power supply for the main power circuit

(X1).

Connect the power supply for the electric booster

heater, if present (KM2, X8).

11_02_200_202_01_012

KM2

Terminal

Description

L1/L2/L3/N Connection from main power circuit (compres-

sor and fan) to three-phase alternating current

L/N/PE

Connection from main power circuit (compres-

sor and fan) to single phase alternating current

L1/N

Connection for fan power supply (for outdoor

unit)

TK1/TK2

Fan fault message

L/N

Mains connection for control circuit (OTE)

LS/21

PSU signal contact

KM2 L1/L2/L3

Mains connection for the electric booster

heater (comprising three individual heating

elements)

N/N/N

Information

Connect the PE conductor from the power cables

to the earth rail in the control box.

WARNING: Electrocution

When the appliance power supply is on, there will

always be 230 VAC at the PSU signal contact.

When using the PSU signal contact („PSU signal contact“

on page 24), please note the following:

Remove the factory-fitted clamp on X3 (LS/21).

Connect the cable for the PSU signal contact to X3

(LS/21).

11_02_200_202_01_015

10.4.3 Electrical connection of the outdoor unit

The outdoor unit receives its power supply via the indoor

unit.

Remove the side casing panel from the outdoor unit

to gain access to the terminal box (see „Disassem-

bling the appliance casing“ on page 26).

Connect the fan power supply in the terminal box.

Connect the lead for the defrost sensors (TQE, TQA).

Connect the fan speed lead (0-10 VDC). Make sure

that the polarity of the lead is correct.

Connect the lead for suction gas sensor S2 to the ter-

minal provided.

Connect the cable for the stepper motor of expan-

sion valve A (located in the outdoor unit). Be sure

that each wire is connected correctly according to its

colour.

Содержание AIR 7





































































































Результаты поиска

Содержание AIR 7

Отзывы:

Похожие инструкции для AIR 7

Бренды по названию

Популярные бренды

Ochsner AIR 7, Руководство по эксплуатации и установке

Результаты поиска

Содержание AIR 7

Отзывы:

Похожие инструкции для AIR 7

Бренды по названию

Популярные бренды