Ochsner AIR 7 страница 26 Скачать руководство пользователя

Страница: 26 / 100

INSTALLATION | Appliance installation

www.ochsner.com | 982000-AIR-M2-M4-EN03.1

11_02_200_214_01_002

Material damage

When being transported with the appliance cas-

ing disassembled, sensitive components will be

exposed.

Take care transporting the appliance.

10.1.2 Positioning the appliance

Position the appliance at the intended installation

location.

Use the pre-installed transport aids (2 lifting slings at

the front and 2 lifting handles at the rear) to slide and

tilt the appliance.

Observe minimum clearances.

Ensure the appliance is horizontal. To compen-

sate for minor unevenness in the floor, use the four

height-adjusting plastic glides on the underside of the

appliance.

Information

On the underside of the indoor unit, there are four

plastic glides with rubber mounted threaded pins

(without nuts).

Discrepancies in floor height of up

to 6 mm can be compensated for.

11_02_200_214_01_003

1 Lifting sling

2 Mounting bolt

3 Appliance frame

After the appliance has been placed in position,

remove the two lifting slings at the front of the

appliance.

Undo and remove the two mounting bolts and remove

the two lifting slings.

Then screw the two mounting bolts back into the ap-

pliance frame.

10.1.3 Disassembling the appliance casing

11_02_200_214_01_006

Undo and remove the four knurled screws for the ap-

pliance casing panel at the rear of the appliance.

Undo and remove the two fixing screws for the control

box cover, on the rear of the appliance.

11_02_200_214_01_007

Slide back the control box cover. Lift the control box

cover up and away.

Содержание AIR 7





































































































Результаты поиска

Содержание AIR 7

Отзывы:

Похожие инструкции для AIR 7

Бренды по названию

Популярные бренды

Ochsner AIR 7, Руководство по эксплуатации и установке

Результаты поиска

Содержание AIR 7

Отзывы:

Похожие инструкции для AIR 7

Бренды по названию

Популярные бренды