Ochsner AIR 7 страница 17 Скачать руководство пользователя

Страница: 17 / 100

INSTALLATION | Preparing to install the appliance

982000-AIR-M2-M4-EN03.1 | www.ochsner.com 17

11_06_200_202_006

1 Flat roof

2 Refrigerant lines in open air (enclosed in thermal in-

sulation with UV protection)

2x concrete slabs attached with flexible adhesive (per

leg of the outdoor unit). The outdoor unit is affixed to

the concrete slabs

4 Anti-vibration mounts

When installing the outdoor unit on a freestanding car port,

a garage roof or a storage space roof, please note the

following:

Ensure that the outdoor unit is adequately secured,

paying regard to the wind load occurring at the instal-

lation location.

Take account of the concentrated load arising from

the dead weight of the outdoor unit (including the

roof fixings) and the surface load caused by possible

build-up of ice.

Ensure suitable structure-borne sound separation be-

tween the outdoor unit and the installation points on

the roof.

9.4 Preparing the refrigerant lines

Information

If the appliance, the refrigerant lines, the pipe fix

ings and the wall outlets are not installed correctly,

structure-borne sounds can be transmitted to the

building.

Ensure that the refrigerant lines are in-

stalled in a way that ensures insulation from

structure-borne noise. The system installer

carrying out the work is responsible for this.

Material damage

Use only copper pipes suitable for refrigerant

(DIN 12735-1). Thin-walled pipes run the risk of

bursting.

Please observe the stipulated diameters and

wall thicknesses of the copper pipes.

Material damage

Incorrect or premature opening of the pipe connec-

tions and cutting of the refrigerant lines can allow

dirt and moisture to enter the refrigerant circuit.

Do not open the connections on the indoor

or outdoor units until just before installing the

refrigerant lines.

Cut the refrigerant lines with a suitable pipe

cutter.

Prevent swarf from contaminating the pipe

connections and refrigerant lines.

Once cut, fill the refrigerant lines with a sub

stance such as nitrogen.

Keep the refrigerant lines closed until just be-

fore installation.

Pipe connections for the refrigerant lines (suction gas and

liquid lines) are supplied soldered closed, both for the in-

door unit and the outdoor unit. Appropriate copper pipes

for refrigerant lines are supplied sealed at both ends and

filled with nitrogen.

Please note the following with regard to routing of the re-

frigerant lines:

Keep to a minimum the distance between the indoor

and outdoor units, in order to minimise heat loss from

the refrigerant lines.

Select the installation sites for the indoor and outdoor

units such that the maximum permissible line lengths

and height differentials are not exceeded.

Avoid routing the lines in the vicinity of bedrooms.

The refrigerant in the lines can generate noise under

certain operational conditions.

Содержание AIR 7





































































































Результаты поиска

Содержание AIR 7

Отзывы:

Похожие инструкции для AIR 7

Бренды по названию

Популярные бренды

Ochsner AIR 7, Руководство по эксплуатации и установке

Результаты поиска

Содержание AIR 7

Отзывы:

Похожие инструкции для AIR 7

Бренды по названию

Популярные бренды