manualshive.com logo in svg

Oberheim MC 3000, Руководство по эксплуатации

Поделиться
Скачать
Oberheim MC 3000 Скачать руководство пользователя страница 38

MC 3000

Operating Manual

108

1. Press function key F1 (EDIT) to obtain the EDIT CHAIN page on the display; the

PROGRAM N.: field is automatically selected, indicating the patch which corresponds to
step 1 of the selected chain.

2. Modify the patch set in the PROGRAM N. field

 

 

 

3. Press function key F6 to actually assign the selected patch to the current step.  At this

point, the step will automatically set on step n. 2.

4. Repeat the entire procedure for all the steps you wish, bearing in mind that you can

move the step selection using the function keys F5 and F6.

5. If you wish to make corrections to any step, position on the step (F5 and F6 keys) and

delete the current step (DEL) or insert a new one (INS).

6. When last step is reached, select the field STEP CHANGE (using the cursor keys) and

choose your preferred step change mode.

7. Press WRITE: the following video page will appear.

 

 

 

8. Press the F5 (NAME) function key and type the name of the chain using the

alphanumeric keypad, the INC and DEC keys, or by turning the encoder and moving
around with the cursor keys

9. Press function key F6 (DONE) and the previous video page will return to the display.

 

The MC 3000 places no less than 128 chains, each of which can contain up to 256
steps, at the user's disposal.

 
 
 
 
 
 
 
 

Edit selected
chain

Содержание MC 3000













































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды