manualshive.com logo in svg

NXP Semiconductors SAFE ASSURE Qorivva MPC5601P, Справочное руководство

NXP Semiconductors SAFE ASSURE Qorivva MPC5601P - Руководство по эксплуатации для этой мощной полупроводниковой продукции доступно для бесплатного скачивания на нашем сайте. Это детальное "Reference Manual" обязательно поможет вам использовать устройство эффективно и безопасно. Скачайте его с manualshive.com.

Поделиться
Скачать
background image

Chapter 24 Cross Triggering Unit (CTU)

MPC5602P Microcontroller Reference Manual, Rev. 4

612

Freescale Semiconductor

 

value written into the double-buffered register (TGSCRR), during the control cycle 

n

– 1 and reloads all 

the double-buffered registers (such as Trigger Compare registers, TGSCR, TGSCRR itself). 

The triggers list registers consist of eight compare registers. Each triggers list register is associated with a 
comparator. On reload (MRS occurrence), the comparators are disabled. One TGS clock cycle is necessary 
to enable them and to start the counting. The MRS is output together with individual trigger signals. The 
MRS can be performed by hardware or by software. The MRS_SG bit in the CTU control register, if set 
to 1, generates equivalent software MRS (that is, resets/reloads TGS Counter and reloads all 
double-buffered registers). This bit is cleared by each hardware or software MRS occurrence.

The TGS counter compare register and the TGS counter comparator are used to stop the TGS counter when 
it reaches the value stored in the TGS counter compare register before an MRS occurs.

The prescaler for TGS and SU can be 1,2,3,4 (PRES bits in the TGS Control Register).

An example timing for the TGS in Triggered Mode is shown in 

Figure 24-3

. The red arrows indicate the 

MRS occurrences, while the black arrows indicate the trigger event occurrences, with the relevant delay 
in respect to the last MRS occurrence.

Figure 24-3. Example timing for TGS in triggered mode

24.3.4

TGS in sequential mode

The structure of the TGS in sequential mode is shown in 

Figure 24-4

. 

The 32 input events (16 signals with two edges for signal), which can be individually enabled, are ORed 
in order to generate the event signal (ES). The ES enables the reload of the TGS counter register and pilots 
the 3-bit counter in order to select the next active trigger. One of the 32 input events can be selected, 
through the MRS_SM (master reload selection sequential mode) bits in the TGS control register, to be the 
MRS, that enables the reload of the triggers list and resets the 3-bit counter (incoming events counter), that 
is, the MRS is the signal linked with the control cycle defined as the time window between two consecutive 
MRSs. In this mode, each incoming event sequentially enables only one trigger event through the 3-bit 
counter and the MUX. The MUX is a selection switch that enables, according to the number of event 
signals occurred, only one of the eight trigger signals to the scheduler subunit. Sequences of as many as 
eight trigger events can be supported within this control cycle. 

For the other features see the previous paragraphs.

Delay T

0

 

Delay T

1

 

Delay T

2

 

Delay T

2

 

Содержание SAFE ASSURE Qorivva MPC5601P



























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SAFE ASSURE Qorivva MPC5601P

Galcon 6100 Series Installation And Operating Instructions Manual preview
6100 Series
Бренд: Galcon Страницы: 32
Lantronix xPico 200 Series Manual preview
xPico 200 Series
Бренд: Lantronix Страницы: 7
Lantronix xPico 110 Quick Start Manual preview
xPico 110
Бренд: Lantronix Страницы: 3
Lantronix EDS1100 Quick Start Manual preview
EDS1100
Бренд: Lantronix Страницы: 15
Parker AC890PX Series User Mounting And Assembly Instructions preview
AC890PX Series
Бренд: Parker Страницы: 30
Parker Compax3M Series Installation Manual preview
Compax3M Series
Бренд: Parker Страницы: 52
Parker AC30V Series Manual preview
AC30V Series
Бренд: Parker Страницы: 337
W.E.ST. SCU-138-P Technical Documentation Manual preview
SCU-138-P
Бренд: W.E.ST. Страницы: 34
Ltech TT-DX-R4-5A Manual preview
TT-DX-R4-5A
Бренд: Ltech Страницы: 4
Motor Guard M-60R Instructions preview
M-60R
Бренд: Motor Guard Страницы: 2
Samcen SCS8000E Administrator'S Manual preview
SCS8000E
Бренд: Samcen Страницы: 65
National Instruments sbRIO-9698 User Manual preview
sbRIO-9698
Бренд: National Instruments Страницы: 12
Doepke RJSG 1 Installation And Operating Manual preview
RJSG 1
Бренд: Doepke Страницы: 2
Genius BRAIN 06 24V Manual preview
BRAIN 06 24V
Бренд: Genius Страницы: 52
Neousys Technology Nuvo-3000 Series User Manual preview
Nuvo-3000 Series
Бренд: Neousys Technology Страницы: 101
KORINS EPIP-40 /30A(I) Instruction Manual preview
EPIP-40 /30A(I)
Бренд: KORINS Страницы: 3
Linear Technology LTC4232 Demo Manual preview
LTC4232
Бренд: Linear Technology Страницы: 6
Martin Audio CMX2A Specification Sheet preview
CMX2A
Бренд: Martin Audio Страницы: 1

Бренды по названию

Популярные бренды

Загрузить еще бренды