manualshive.com logo in svg

NXP Semiconductors SAFE ASSURE Qorivva MPC5601P, Справочное руководство

NXP Semiconductors SAFE ASSURE Qorivva MPC5601P - Руководство по эксплуатации для этой мощной полупроводниковой продукции доступно для бесплатного скачивания на нашем сайте. Это детальное "Reference Manual" обязательно поможет вам использовать устройство эффективно и безопасно. Скачайте его с manualshive.com.

Поделиться
Скачать
background image

Chapter 17 Flash Memory

MPC5602P Microcontroller Reference Manual, Rev. 4

378

Freescale Semiconductor

 

A software mechanism is provided to independently lock/unlock each Low or Mid Address Space block 
against program and erase.

Software locking is done through the LML (Low/Mid Address Space Block Lock Register) register.

An alternate means to enable software locking for blocks of Low Address Space only is through the SLL 
(Secondary Low/Mid Address Space Block Lock Register).

All these registers have a non-volatile image stored in TestFlash (NVLML, NVSLL), so that the locking 
information is kept on reset.

On delivery the TestFlash non-volatile image is at all 1s, meaning all sectors are locked.

By programming the non-volatile locations in TestFlash, the selected sectors can be unlocked.

Because the TestFlash is one-time programmable (that is, not erasable), once the sectors have been 
unlocked, they cannot be locked again. 

Of course, on the contrary, all the volatile registers can be written at 0 or 1 at any time, therefore the user 
application can lock and unlock sectors when desired.

17.3.8.4.2

Censored mode

The Censored mode information is stored in non-volatile Flash cells located in the Shadow Sector. This 
information is read once during the Flash initialization phase following the exit from Reset and they are 
stored in Volatile registers that act as actuators.

The reset state of all the volatile censored mode registers is the protected state. 

All the non-volatile censored mode registers can be programmed through a normal double word program 
operation at the related locations in the Shadow Sector.

The non-volatile censored mode registers can be erased by erasing the Shadow Sector.

•

The non-volatile censored mode registers are physically located in the Shadow Sector their bits can 
be programmed to 0 and eventually restored to 1 by erasing the Shadow Sector. 

•

The volatile censored mode registers are registers not accessible by the user application.

The Flash block provides two levels of protection against piracy:

•

If bits NVSCI0[CW[15:0]] are programmed to 0x55AA and NVSC1 = NVSCI0, Censored mode 
is disabled. All other possible values enable Censored mode.

•

If bits NVSCI0[SC[15:0]] are programmed to 0x55AA and NVSC1 = NVSCI0, Public Access is 
disabled. All other possible values enable Public Access.

The parts are delivered to the user with Censored mode and public access disabled.

The chosen Flash ECC algorithm allows to modify the censorship status without erasing the Shadow 
sector, as shown in 

Table 17-38

.

Содержание SAFE ASSURE Qorivva MPC5601P



























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SAFE ASSURE Qorivva MPC5601P

ABB LME620-AI Service Instruction preview
LME620-AI
Бренд: ABB Страницы: 30
ABB LME620-AI Instructions Manual preview
LME620-AI
Бренд: ABB Страницы: 15
ABB PST30 Manual preview
PST30
Бренд: ABB Страницы: 10
ABB LME620-AI User Manual preview
LME620-AI
Бренд: ABB Страницы: 44
Eaton S701 Instruction Leaflet preview
S701
Бренд: Eaton Страницы: 8
Allen-Bradley 1756-L72EROM Installation Instructions Manual preview
1756-L72EROM
Бренд: Allen-Bradley Страницы: 16
Westlock DIGITAL EPIC-2 DTM User Manual preview
DIGITAL EPIC-2 DTM
Бренд: Westlock Страницы: 33
Varian Turbo-V 250 series Instruction Manual preview
Turbo-V 250 series
Бренд: Varian Страницы: 79
Cypress CY3643 Quick Start Manual preview
CY3643
Бренд: Cypress Страницы: 2
Dudley Wave S3 Manual preview
Wave S3
Бренд: Dudley Страницы: 8
Parker Sporlan 952567 Installation And Operation Instructions Manual preview
Sporlan 952567
Бренд: Parker Страницы: 24
Holars AS H-TAG User Manual preview
H-TAG
Бренд: Holars AS Страницы: 15
Sulion Driver VISIO IoT Manual preview
Driver VISIO IoT
Бренд: Sulion Страницы: 8
Sentiotec K2-NEXT Installation And Operating Instructions Manual preview
K2-NEXT
Бренд: Sentiotec Страницы: 92
CDVI Ievo User Manual preview
Ievo
Бренд: CDVI Страницы: 24
Danfoss OBC 80 Series Manual preview
OBC 80 Series
Бренд: Danfoss Страницы: 16
Ibiza LC192DMX-MINI User Manual preview
LC192DMX-MINI
Бренд: Ibiza Страницы: 37
hager RTQ520X Manual preview
RTQ520X
Бренд: hager Страницы: 10

Бренды по названию

Популярные бренды

Загрузить еще бренды