manualshive.com logo in svg

NXP Semiconductors SAFE ASSURE Qorivva MPC5601P, Справочное руководство

NXP Semiconductors SAFE ASSURE Qorivva MPC5601P - Руководство по эксплуатации для этой мощной полупроводниковой продукции доступно для бесплатного скачивания на нашем сайте. Это детальное "Reference Manual" обязательно поможет вам использовать устройство эффективно и безопасно. Скачайте его с manualshive.com.

Поделиться
Скачать
background image

Chapter 22 FlexCAN

MPC5602P Microcontroller Reference Manual, Rev. 4

546

Freescale Semiconductor

 

6

SOFT_RST

Soft Reset
When this bit is asserted, FlexCAN resets its internal state machines and some of the memory 
mapped registers. The following registers are reset: MCR (except the MDIS bit), TIMER, ECR, ESR, 
IMASK1, IFLAG1. Configuration registers that control the interface to the CAN bus are not affected 
by soft reset. The following registers are unaffected: 
  • CTRL 
 • RXIMR0–RXIMR31
 • RXGMASK, RX14MASK, RX15MASK
 • all Message Buffers
The SOFT_RST bit can be asserted directly by the CPU when it writes to the MCR, but it is also 
asserted when global soft reset is requested at MCU level. Since soft reset is synchronous and has 
to follow a request/acknowledge procedure across clock domains, it may take some time to fully 
propagate its effect. The SOFT_RST bit remains asserted while reset is pending, and is 
automatically negated when reset completes. Therefore, software can poll this bit to know when the 
soft reset has completed. 
Soft reset cannot be applied while clocks are shut down in any of the low power modes. The module 
should be first removed from low power mode, and then soft reset can be applied.
0 No reset request. 
1 Resets the registers marked as “affected by soft reset” in 

Table 22-2

. 

7

FRZ_ACK

Freeze Mode Acknowledge
This read-only bit indicates that FlexCAN is in Freeze mode and its prescaler is stopped. The Freeze 
mode request cannot be granted until current transmission or reception processes have finished. 
Therefore the software can poll the FRZ_ACK bit to know when FlexCAN has actually entered 
Freeze Mode. If Freeze mode request is negated, then this bit is negated once the FlexCAN 
prescaler is running again. If Freeze mode is requested while FlexCAN is in any of the low power 
modes, then the FRZ_ACK bit will only be set when the low power mode is exited. See 

Section 22.4.9.1, “Freeze mode

 for more information.

0 FlexCAN not in Freeze mode, prescaler running. 
1 FlexCAN in Freeze mode, prescaler stopped. 

8

SUPV

Supervisor Mode
This bit configures some of the FlexCAN registers to be either in Supervisor or Unrestricted memory 
space. The registers affected by this bit are marked as S/U in the Access Type column of 

Table 22-2

. 

The reset value of this bit is 1, so the affected registers start with Supervisor access restrictions. 
0 Affected registers are in Unrestricted memory space. 
1 Affected registers are in Supervisor memory space. Any access without supervisor permission 

behaves as though the access was done to an unimplemented register location. 

10

WRN_EN

Warning Interrupt Enable
When asserted, this bit enables the generation of the TWRN_INT and RWRN_INT flags in the Error 
and Status Register. If WRN_EN is negated, the TWRN_INT and RWRN_INT flags will always be 
zero, independent of the values of the error counters, and no warning interrupt will ever be 
generated.
0 TWRN_INT and RWRN_INT bits are zero, independent of the values in the error counters.
1 TWRN_INT and RWRN_INT bits are set when the respective error counter transition from <96 

to 

 96.

Table 22-11. MCR field descriptions (continued)

Field

Description

Содержание SAFE ASSURE Qorivva MPC5601P



























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SAFE ASSURE Qorivva MPC5601P

Y-Solar Smart-MPPT Li Series User Manual preview
Smart-MPPT Li Series
Бренд: Y-Solar Страницы: 6
BADODOSECURITY G200 Quick Manual preview
G200
Бренд: BADODOSECURITY Страницы: 8
Bard ECU Series Advanced Programming & Features preview
ECU Series
Бренд: Bard Страницы: 8
Samson 3372 User Manual preview
3372
Бренд: Samson Страницы: 8
Vageo DT-1 Plus Manual preview
DT-1 Plus
Бренд: Vageo Страницы: 2
Vacon 100 INDUSTRIAL Additional Installation Instruction preview
100 INDUSTRIAL
Бренд: Vacon Страницы: 6
Vacon 100 INDUSTRIAL Technical Manual preview
100 INDUSTRIAL
Бренд: Vacon Страницы: 24
Vacon 100X series Marine Installation Manual preview
100X series
Бренд: Vacon Страницы: 30
Vacon 100 flow User Manual preview
100 flow
Бренд: Vacon Страницы: 81
Vacon 100X series Installation And Maintenance Manual preview
100X series
Бренд: Vacon Страницы: 100
National Instruments 73 Series Getting Started preview
73 Series
Бренд: National Instruments Страницы: 34
Reer MOSAIC MA2 Quick Installation Manual preview
MOSAIC MA2
Бренд: Reer Страницы: 2
Sunlover SL6 ELITE Quick Start Manual preview
SL6 ELITE
Бренд: Sunlover Страницы: 2
OCL DLC-1.1 Quick Start Manual preview
DLC-1.1
Бренд: OCL Страницы: 2
Velp Scientifica F201A0505 Instruction Manual preview
F201A0505
Бренд: Velp Scientifica Страницы: 24
Italtecnica Brio 2000 Owner'S Manual preview
Brio 2000
Бренд: Italtecnica Страницы: 16
fadini Elpro S40 Manual preview
Elpro S40
Бренд: fadini Страницы: 40
Dieffematic LINEA c400 Instructions And Recommendations For The Installer preview
LINEA c400
Бренд: Dieffematic Страницы: 9

Бренды по названию

Популярные бренды

Загрузить еще бренды