NXP Semiconductors SAFE ASSURE Qorivva MPC5601P Скачать руководство пользователя страница 878 | Manualshive

Страница: 878 / 954

background image

Chapter 36 Nexus Development Interface (NDI)

MPC5602P Microcontroller Reference Manual, Rev. 4

878

Freescale Semiconductor

events will not occur when an instruction would not have normally begun execution due to a higher priority
exception at an instruction boundary.

IAC compares perform a 31-bit compare for VLE instructions. Each halfword fetched by the instruction
fetch unit will be marked with a set of bits indicating whether an Instruction Address Compare occurred
on that halfword. Debug exceptions will occur if enabled and a 16-bit instruction, or the first halfword of
a 32-bit instruction, is tagged with an IAC hit.

36.10.2 Data Address Compare Event

Data Address Compare debug events occur when enabled and execution of a load or store class instruction
results in a data access that meets the criteria specified in the DBCR0, DBCR2, DBCR4, DAC1, DAC2,
DVC1, and DVC2 Registers. Data address compares may specify user/supervisor mode and data space
(MSR

DS

), along with an effective address, masked effective address, or range of effective addresses for

comparison. This event can occur and be recorded in DBSR regardless of the setting of MSR

DE

. Two

address compare values (DAC1, DAC2) are provided.

NOTE

In contrast to the Power Architecture technology, Data Address Compare
events on e200z0h do not prevent the load or store class instruction from
completing. If a load or store class instruction completes successfully
without a Data TLB or Data Storage interrupt, Data Address Compare
exceptions are reported at the completion of the instruction. If the exception
results in a precise Debug interrupt, the address value saved in DSRR0 (or
CSRR0 if the Debug APU is disabled) is the address of the instruction
following the load or store class instruction. For DVC DAC events, the
exception can be imprecisely reported even further past the load or store
class instruction generating the event (without necessarily affecting
DBSR

IDE

) and the saved address value can point to a subsequent instruction

past the next instruction. This occurrence is indicated in the
DBSR

DAC_OFST

field.

If a load or store class instruction does not complete successfully due to a
Data Storage exception, and a Data Address Compare debug exception also
occurs, the result is an imprecise Debug interrupt, the address value saved
in DSRR0 (or CSRR0 if the Debug APU is disabled) is the address of the
load or store class instruction, and the DBSR

IDE

bit will be set. In addition

to occurring when DBCR0

IDM

=1, this circumstance can also occur when

DBCR0

EDM

=1.

NOTE

DAC events will not be recorded or counted if a

lmw

or

stmw

instruction is

interrupted prior to completion by a critical input or external input interrupt.

NOTE

DAC events are not signaled on the second portion of a misaligned load or
store that is broken up into two separate accesses.

«
...
876
877
878
879
880
...
»

Содержание SAFE ASSURE Qorivva MPC5601P



























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SAFE ASSURE Qorivva MPC5601P

Бренд: J4C Страницы: 4

Бренд: Omega Страницы: 56

Бренд: Omega Страницы: 2

Бренд: Gardena Страницы: 236

Бренд: TSM Страницы: 2

Бренд: Rheem Страницы: 2

Бренд: L&L KILNS Страницы: 12

Бренд: Evco Страницы: 78

Бренд: VALPES Страницы: 28

Бренд: QUANT Страницы: 24

Бренд: TAC Vista Страницы: 2

Бренд: Ellard Страницы: 21

Бренд: Allen-Bradley Страницы: 162

Driver LED 1x2A/48V

Бренд: PXM Страницы: 11

All Sport 1600 Series

Бренд: Daktronics Страницы: 92

Бренд: Beckhoff Страницы: 15

Бренд: Compaq Страницы: 23

DS-K1F600U-D6E Series

Бренд: HIKVISION Страницы: 49

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды