manualshive.com logo in svg

NXP Semiconductors LPC1311, Руководство пользователя, Страница: 63 / 368

Поделиться
Скачать
NXP Semiconductors LPC1311 Скачать руководство пользователя страница 63

UM10375

All information provided in this document is subject to legal disclaimers.

© NXP B.V. 2011. All rights reserved.

User manual

Rev. 3 — 14 June 2011 

63 of 368

NXP Semiconductors

UM10375

Chapter 6: LPC13xx Interrupt controller

 

[1]

See 

Section 3.1

 for wake-up pins not used in the HVQFN package.

Table 66.

Connection of interrupt sources to the Vectored Interrupt Controller

Exception 
Number

Vector 
Offset

Function

Flag(s)

39 to 0

start logic wake-up 
interrupts

Each interrupt is connected to a PIO input pin serving 
as wake-up pin from Deep-sleep mode (see 

Section 3.5.37

 and 

Section 3.5.41

). 

Interrupts 0 to 11 are connected to PIO0_0 to 
PIO0_11; interrupts 12 to 23 are connected to 
PIO1_0 to PIO1_11; interrupts 24 to 35 are 
connected to PIO2_0 to PIO2_11; interrupts 36 to 39 
are connected to PIO3_0 to PIO3_3.

[1]

 

40

0xA0

I2C0

SI (state change)

41

0xA4

CT16B0 

Match 0 - 2

Capture 0 

42

0xA8

CT16B1 

Match 0 - 1

Capture 0 

43

0xAC

CT32B0 

Match 0 - 3

Capture 0 

44

0xB0

CT32B1 

Match 0 - 3

Capture 0 

45

0xB4

SSP0

Tx FIFO half empty

Rx FIFO half full

Rx Timeout

Rx Overrun

46

0xB8

UART

Rx Line Status (RLS)

Transmit Holding Register Empty (THRE)

Rx Data Available (RDA)

Character Time-out Indicator (CTI)

Modem Control Change
End of Auto-Baud (ABEO)
Auto-Baud Time-Out (ABTO)

47

0xBC

USB IRQ interrupt 

USB low-priority interrupt

48

0xC0

USB FIQ interrupt

USB high-priority interrupt

49

0xC4

ADC

A/D Converter end of conversion

50

0xC8

WDT

Watchdog interrupt (WDINT)

51

0xCC

BOD

Brown-out detect

52

-

-

Reserved

53

0xD4

PIO_3

GPIO interrupt status of port 3

54

0xD8

PIO_2

GPIO interrupt status of port 2

55

0xDC

PIO_1

GPIO interrupt status of port 1

56

0xE0

PIO_0

GPIO interrupt status of port 0

57

0xE4

SSP1

Tx FIFO half empty

Rx FIFO half full

Rx Timeout

Rx Overrun

Содержание LPC1311

















































































































































































































































































































































































Отзывы:

Нет отзывов