manualshive.com logo in svg

NXP Semiconductors LPC1311, Руководство пользователя, Страница: 182 / 368

Поделиться
Скачать
NXP Semiconductors LPC1311 Скачать руководство пользователя страница 182

UM10375

All information provided in this document is subject to legal disclaimers.

© NXP B.V. 2011. All rights reserved.

User manual

Rev. 3 — 14 June 2011 

182 of 368

NXP Semiconductors

UM10375

Chapter 12: LPC13xx UART

 

[1]

Reset Value reflects the data stored in used bits only. It does not include reserved bits content.

Table 193. Register overview: UART (base address: 0x4000 8000)

Name

Access Address 

offset

Description

Reset 
value

[1]

U0RBR

RO

0x000 

Receiver Buffer Register. Contains the next received character to be read. 
When DLAB=0.

NA

U0THR

WO

0x000 

Transmit Holding Register. The next character to be transmitted is written 
here. When DLAB=0.

NA

U0DLL

R/W

0x000

Divisor Latch LSB. Least significant byte of the baud rate divisor value. The 
full divisor is used to generate a baud rate from the fractional rate divider. 
When DLAB=1.

0x01

U0DLM

R/W

0x004 

Divisor Latch MSB. Most significant byte of the baud rate divisor value. The 
full divisor is used to generate a baud rate from the fractional rate divider. 
When DLAB=1.

0x00

U0IER

R/W

0x004 

Interrupt Enable Register. Contains individual interrupt enable bits for the 7 
potential UART interrupts. When DLAB=0.

0x00

U0IIR

RO

0x008

Interrupt ID Register. Identifies which interrupt(s) are pending.

0x01

U0FCR

WO

0x008

FIFO Control Register. Controls UART FIFO usage and modes.

0x00

U0LCR

R/W

0x00C

Line Control Register. Contains controls for frame formatting and break 
generation.

0x00

U0MCR

R/W

0x010

Modem control register

0x00

U0LSR

RO

0x014

Line Status Register. Contains flags for transmit and receive status, 
including line errors.

0x60

U0MSR

RO

0x018

Modem status register

0x00

U0SCR

R/W

0x01C

Scratch Pad Register. Eight-bit temporary storage for software.

0x00

U0ACR

R/W

0x020

Auto-baud Control Register. Contains controls for the auto-baud feature.

0x00

-

-

0x024

Reserved -

U0FDR

R/W

0x028

Fractional Divider Register. Generates a clock input for the baud rate 
divider.

0x10

-

-

0x02C

Reserved

-

U0TER

R/W

0x030

Transmit Enable Register. Turns off UART transmitter for use with software 
flow control.

0x80

-

-

0x034 - 
0x048

Reserved

-

U0RS485CTRL R/W

0x04C

RS-485/EIA-485 Control. Contains controls to configure various aspects of 
RS-485/EIA-485 modes.

0x00

U0RS485ADR
MATCH

R/W

0x050

RS-485/EIA-485 address match. Contains the address match value for 
RS-485/EIA-485 mode.

0x00

U0RS485DLY

R/W

0x054

RS-485/EIA-485 direction control delay.

0x00

Содержание LPC1311

















































































































































































































































































































































































Отзывы:

Нет отзывов