manualshive.com logo in svg

NXP Semiconductors LPC1311, Руководство пользователя, Страница: 316 / 368

Поделиться
Скачать
NXP Semiconductors LPC1311 Скачать руководство пользователя страница 316

UM10375

All information provided in this document is subject to legal disclaimers.

© NXP B.V. 2011. All rights reserved.

User manual

Rev. 3 — 14 June 2011 

316 of 368

NXP Semiconductors

UM10375

Chapter 20: LPC13xx Analog-to-Digital Converter (ADC)

20.6.3 A/D Interrupt Enable Register (AD0INTEN - 0x4001 C00C)

This register allows control over which A/D channels generate an interrupt when a 
conversion is complete. For example, it may be desirable to use some A/D channels to 
monitor sensors by continuously performing conversions on them. The most recent 
results are read by the application program whenever they are needed. In this case, an 
interrupt is not desirable at the end of each conversion for some A/D channels.

 

20.6.4 A/D Data Registers (AD0DR0 to AD0DR7 - 0x4001 C010 to 

0x4001 C02C)

The A/D Data Register hold the result when an A/D conversion is complete, and also 
include the flags that indicate when a conversion has been completed and when a 
conversion overrun has occurred.

 

20.6.5 A/D Status Register (AD0STAT - 0x4001 C030)

The A/D Status register allows checking the status of all A/D channels simultaneously. 
The DONE and OVERRUN flags appearing in the AD0DRn register for each A/D channel 
are mirrored in ADSTAT. The interrupt flag (the logical OR of all DONE flags) is also found 
in ADSTAT.

Table 307: A/D Interrupt Enable Register (AD0INTEN - address 0x4001 C00C) bit description

Bit

Symbol

Description

Reset 
Value

7:0

ADINTEN

These bits allow control over which A/D channels generate 
interrupts for conversion completion. When bit 0 is one, completion 
of a conversion on A/D channel 0 will generate an interrupt, when bit 
1 is one, completion of a conversion on A/D channel 1 will generate 
an interrupt, etc.

0x00

8

ADGINTEN

When 1, enables the global DONE flag in ADDR to generate an 
interrupt. When 0, only the individual A/D channels enabled by 
ADINTEN 7:0 will generate interrupts.

1

31:9 -

Reserved.

0

Table 308: A/D Data Registers (AD0DR0 to AD0DR7 - addresses 0x4001 C010 to 

0x4001 C02C) bit description

Bit

Symbol

Description

Reset 
Value

5:0

-

Reserved.

0

15:6

V_VREF

When DONE is 1, this field contains a binary fraction representing the 
voltage on the ADn pin, divided by the voltage on the V

REF

 pin. Zero in 

the field indicates that the voltage on the ADn pin was less than, equal 
to, or close to that on V

REF

, while 0x3FF indicates that the voltage on 

AD input was close to, equal to, or greater than that on V

REF

.

NA

29:16 -

Reserved.

0

30

OVERRUN This bit is 1 in burst mode if the results of one or more conversions 

was (were) lost and overwritten before the conversion that produced 
the result in the V_VREF bits.This bit is cleared by reading this 
register.

0

31

DONE

This bit is set to 1 when an A/D conversion completes. It is cleared 
when this register is read.

0

Содержание LPC1311

















































































































































































































































































































































































Отзывы:

Нет отзывов