NXP Semiconductors LPC1311 Скачать руководство пользователя страница 181

Страница: 181 / 368

UM10375

All information provided in this document is subject to legal disclaimers.

User manual

Rev. 3 — 14 June 2011

181 of 368

NXP Semiconductors

UM10375

Chapter 12: LPC13xx UART

[1]

LQFP48 packages only.

12.5 Clocking and power control

The clocks and power to the UART block are controlled by two registers:

1. The UART block can be enabled or disabled through the System AHB clock control

Table 25

2. The UART peripheral clock UART_PCLK is enabled in the UART clock divider

Table 27

). This clock is used by the UART baud rate generator.

Remark:

For LPC1311/13/42/43 parts, the UART pins must be configured in the

corresponding IOCON registers

before

the UART clocks are enabled. For the

LPC1311/01 and LPC1313/01 parts, no special enabling sequence is required.

12.6 Register description

The UART contains registers organized as shown in

Table 193

. The Divisor Latch Access

Bit (DLAB) is contained in U0LCR[7] and enables access to the Divisor Latches.

CTS

Input

Clear To Send.

DCD

[1]

Input

Data Carrier Detect.

[1]

Input

Ring Indicator.

Table 192. UART pin description

Pin

Type

Description

Содержание LPC1311

















































































































































































































































































































































































Результаты поиска

Содержание LPC1311

Отзывы:

NXP Semiconductors LPC1311, Руководство пользователя, Страница: 181 / 368

Результаты поиска

Содержание LPC1311

Отзывы: