manualshive.com logo in svg

NXP Semiconductors LPC1311, Руководство пользователя, Страница: 18 / 368

Поделиться
Скачать
NXP Semiconductors LPC1311 Скачать руководство пользователя страница 18

UM10375

All information provided in this document is subject to legal disclaimers.

© NXP B.V. 2011. All rights reserved.

User manual

Rev. 3 — 14 June 2011 

18 of 368

NXP Semiconductors

UM10375

Chapter 3: LPC13xx System configuration

 

3.5.4 System PLL status register

This register is a Read-only register and supplies the PLL lock status (see 

Section 3.11.1

).

 

3.5.5 USB PLL control register

The USB PLL is identical to the system PLL and is used to provide a dedicated clock to 
the USB block if available (see 

Section 3.1

). 

This register connects and enables the USB PLL and configures the PLL multiplier and 
divider values. The PLL accepts an input frequency from 10 MHz to 25 MHz from various 
clock sources. The input frequency is multiplied up to a high frequency, then divided down 
to provide the actual clock 48 MHz clock used by the USB subsystem.

Remark: 

The USB PLL must be connected to the system oscillator for correct USB 

operation (see 

Table 20

).

 

Table 10.

System PLL control register (SYSPLLCTRL, address 0x4004 8008) bit description

Bit

Symbol

Value

Description

Reset 
value

4:0

MSEL

Feedback divider value. The division value M is the 
programmed MSEL value + 1.
00000: Division ratio M = 1
to
11111: Division ratio M = 32.

0x000

6:5

PSEL

Post divider ratio P. The division ratio is 2 

 P.

0x00

0x0

P = 1

0x1

P = 2

0x2

P = 4

0x3

P = 8

31:7

-

-

Reserved. Do not write ones to reserved bits.

0x00

Table 11.

System PLL status register (SYSPLLSTAT, address 0x4004 800C) bit description

Bit

Symbol

Value

Description

Reset 
value

0

LOCK

PLL lock status

0x0

0

PLL not locked

1

PLL locked

31:1

-

-

Reserved

0x00

Table 12.

USB PLL control register (USBPLLCTRL, address 0x4004 8010) bit description

Bit

Symbol

Value

Description

Reset 
value

4:0

MSEL

Feedback divider value. The division value M is the 
programmed MSEL value + 1.
00000: Division ratio M = 1
to
11111: Division ratio M = 32.

0x000

Содержание LPC1311

















































































































































































































































































































































































Отзывы:

Нет отзывов