Nuvation Energy NUV100-CI-12-1 Скачать руководство пользователя страница 53

Страница: 53 / 109

Figure 43. Three possible Nuvation Energy BMS operation states

The normal state is

All OK

and the color of the indicator will be green. The warning state is

Warning

and the color of the indicator will be orange. The fault state is

Fault

and the color of the indicator will

be red.

Clicking on the indicator will jump to a comprehensive status list of warnings and faults active in the
battery stack.

Clicking on the

Clear

button below the state will cancel any warnings and faults that are not self-

clearing.

6.1.8.2. Connection State

The battery stack connection state is shown in the oval indicator.

Figure 44. Three possible connection states

Stack Disconnected

in a red oval indicates the battery stack is unavailable to be charged or discharged.

Stack Pre-charging

in an orange oval indicates the battery stack has connected its pre-charge circuit

and is attempting to equalize the battery stack voltage to the system DC bus voltage.

Stack Connected

in a green oval indicates the battery stack is available to be charged or discharged.

Clicking the

Connect

button initiates the stack connection sequence of events. Nuvation Energy BMS

must be in the

All OK

state for the

Connect

button to be available.

Clicking the

Disconnect

button will disconnect the battery stack from the system DC bus.

6.1.8.3. Information Table

The information table shows the number of cells that are having excess energy bled off to maintain a
balanced battery stack.

Nuvation Energy High-Voltage BMS - Product Manual

Document ID: NE-PM-003

Rev 1.2, 2021-03-03

Curie Update 1

Содержание NUV100-CI-12-1














































































































Результаты поиска

Содержание NUV100-CI-12-1

Отзывы:

Похожие инструкции для NUV100-CI-12-1

Бренды по названию

Популярные бренды

Nuvation Energy NUV100-CI-12-1, Руководство по эксплуатации продукта

Результаты поиска

Содержание NUV100-CI-12-1

Отзывы:

Похожие инструкции для NUV100-CI-12-1

Бренды по названию

Популярные бренды