Nuvation Energy NUV100-CI-12-1 Скачать руководство пользователя страница 67 | Manualshive

Страница: 67 / 109

background image

7. Communication Protocols

7.1. Modbus Protocol Support

Nuvation Energy BMS implements the SunSpec battery models defined in the Modular Energy Storage
Architecture (MESA) as the top-level Modbus interface to the product. Specifically the BMS
implements the MESA Draft 3 Storage models (800 Series).

The specifications for these models are available for download at

https://www.nuvationenergy.com/

technical-resources

.



MESA Draft 3 is currently implemented on Nuvation Energy BMS.

7.1.1. Modbus TCP

This protocol is used for communications over TCP/IP networks. A single Modbus TCP connection is
supported over port 502 for read and write access. All register data is transmitted as big endian
(most significant byte first).

7.1.2. Implemented MESA Models

The MESA standards contain a number of 'models' that can be implemented by vendors to describe a
storage device at various levels of detail. The models implemented by Nuvation Energy BMS are
described in the sections below.

Detailed register maps for all Draft 3 models are found in the document

MESA-Energy-Storage-

Information-Models_Draft_3.xlsx

found at the Nuvation Energy technical resources located at

https://www.nuvationenergy.com/technical-resources

7.1.2.1. Common Model

This model primarily contains information to identify the device (e.g. manufacturer, model, serial
number) as well as the version of software running on the device. A full description of the Common
Model can be found in the SunSpec specification bundle.

7.1.2.2. S801

This model describes an energy storage device at the highest possible level. State-of-Charge and
overall alarm and warning states are found here. All mandatory points are implemented. The Modbus
address of this model is 40070.

7.1.2.3. S802

This model describes a battery storage device. At this level, the critical operational information
includes the charge and discharge current limits. All mandatory points are implemented. The Modbus
address of this model is 40094.

Nuvation Energy High-Voltage BMS - Product Manual

Document ID: NE-PM-003

63

Rev 1.2, 2021-03-03

Curie Update 1

«
...
65
66
67
68
69
...
»

Содержание NUV100-CI-12-1














































































































Отзывы:

Нет отзывов

Похожие инструкции для NUV100-CI-12-1

Бренд: Aalborg Страницы: 128

Бренд: Hardi Страницы: 2

Бренд: YASKAWA Страницы: 64

Бренд: V2 Страницы: 3

Бренд: NEC Страницы: 146

SolarCell Remote

Бренд: Samsung Страницы: 2

Бренд: ZETRON Страницы: 3

Бренд: 3M Страницы: 34

Бренд: Federal Signal Corporation Страницы: 60

Бренд: FASTRON. Страницы: 16

Бренд: Magellan Страницы: 44

Бренд: Namron Страницы: 3

Бренд: Unitech Страницы: 55

Бренд: S&C Страницы: 8

Бренд: YASKAWA Страницы: 49

Бренд: M-system Страницы: 17

Бренд: WAGNER Страницы: 60

Бренд: National Instruments Страницы: 14

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды