Nuvation Energy NUV100-CI-12-1 Скачать руководство пользователя страница 90 | Manualshive

Страница: 90 / 109

background image

stack_fault_discharge_current_hi

▪

Fault that is triggered when the stack current is above the

high

discharge fault threshold.

stack_fault_charge_current_hi

▪

Fault that is triggered when any stack current is above the

high

charge fault threshold.

stack_fault_charge_current_under

▪

Fault that is triggered when any stack current is above the

over

charge fault threshold.

10.1.4.1. Initialization Issues

The stack current is measured from the Stack Switchgear unit’s internal Power Interface module’s
Analog Front End (AFE). The following issues can contribute to these faults not initializing:

1. Stack Switchgear unit’s internal Power Interface module’s AFE is not enabled.

•

This may occur if the Stack Switchgear configuration file is incorrectly modified. Contact

[email protected]

for a valid configuration file for the Stack Switchgear.

2. Communication failure between the Stack Switchgear unit’s internal Stack Controller and Power

Interface modules

10.1.5. Pre-charge Faults

stack_fault_precharge_timeout

▪

Fault that is triggered at the end of the pre-charge period if the measured current exceeds the
maximum pre-charge current

stack_fault_precharge_over_current

▪

Fault that is triggered at any time during the pre-charge connection period if the stack current
exceeds the fault threshold

10.1.5.1. Initialization Issues

These faults are directly related to the current faults detailed previously. Refer to

Section 10.1.4.1

for

details.

10.1.6. Contactor Faults

stack_fault_coil_fail

▪

Fault that is generated when there is a difference between the commanded state of the
contactor coil and the observed state read from the hardware. This fault is a consistency check
on the drive state of the coil. This fault will trigger when contactors are unconnected or have a
short in their circuit. If the fault pilot signal is asserted, this fault will trigger and can not be
used to determine if there is a inconsistent contactor drive state.

Nuvation Energy High-Voltage BMS - Product Manual

Document ID: NE-PM-003

86

Rev 1.2, 2021-03-03

Curie Update 1

«
...
88
89
90
91
92
...
»

Содержание NUV100-CI-12-1














































































































Отзывы:

Нет отзывов

Похожие инструкции для NUV100-CI-12-1

Бренд: Eaton Страницы: 16

Бренд: GE Страницы: 8

Бренд: B&G Страницы: 2

Бренд: B&K Страницы: 9

Бренд: Datavideo Страницы: 8

Бренд: Fanimation Страницы: 2

Бренд: M2M Страницы: 24

Бренд: Federal Signal Corporation Страницы: 60

Бренд: FASTRON. Страницы: 16

Бренд: Gardena Страницы: 14

Бренд: Gardena Страницы: 8

Бренд: Vaillant Страницы: 12

Omnicharge Solar OCS 100-20

Бренд: tbs electronics Страницы: 64

Бренд: Osaka Страницы: 12

Бренд: Barco Страницы: 4

Бренд: Waeco Страницы: 168

RC Electronic DPSI LCD

Бренд: Emcotec Страницы: 32

Security Center AZ5140

Бренд: Abus Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды