Nuvation Energy NUV100-CI-12-1 Скачать руководство пользователя страница 34 | Manualshive

Страница: 34 / 109

background image

Thermal Consistency

For safety certified systems, there is an additional constraint on thermal consistency for all
temperature measurements for each Cell Interface. The constraint is described in detail in the
Sensor Fault Detection section within the Nuvation Energy BMS: Safety Manual (available on
request).

4.4.2.1. Connection Procedure

Connect to Surface

It is recommended to use thermally conductive/electrically non-conductive epoxy to adhere the
thermistors to the cells.

Connect to Cell Interface

'Temperature' cable connects to the 'Temperature Sensors' port at the bottom of the Cell
Interface.

4.4.3. Connect Battery Cells Cable

The Battery Cells cable provides cell voltage input and a means for balancing the cells.

Power Requirements

There is no minimum cell voltage requirement when powering the Cell Interface module from the
Link Bus.

However, if powering the Cell Interface - 12 channel module from the cells (i.e. not powering from
the Link Bus, a minimum of 11V must be present between the most negative and most positive
cells.

Similarly, if powering the Cell Interface - 16 channel module or the Cell Interface - 12V 4 channel
module from the cells (i.e. not powering from the Link Bus), the cells are connected as two groups
and a minimum of 11 V must be present between the most negative and most positive cells of
each group.

4.4.3.1. Connection Procedure



The Stack Switchgear is pre-configured to expect a defined battery topology, based
on the information provided to Nuvation Energy during order fulfillment. Connecting
a differing battery topology will result in undesirable Stack Switchgear behavior.
Please contact

[email protected]

if there is a change in battery topology

requiring a Stack Switchgear configuration update.

Connect to Cells

Connect the cables wires to the battery voltage sense leads. The individual wires are labelled to
help with identifying the connections. Verify the cell voltages present on the connector are correct.
While the Cell Interface module is tolerant of most wiring errors, incorrect connections may cause
the cells to discharge.

Refer to the wiring examples below for the specific Cell Interface module used.

Nuvation Energy High-Voltage BMS - Product Manual

Document ID: NE-PM-003

30

Rev 1.2, 2021-03-03

Curie Update 1

«
...
32
33
34
35
36
...
»

Содержание NUV100-CI-12-1














































































































Отзывы:

Нет отзывов

Похожие инструкции для NUV100-CI-12-1

Бренд: Zetkama Страницы: 6

Бренд: Facility Explorer Страницы: 4

Бренд: YOKOGAWA Страницы: 2

ALICAT SCIENTIFIC PC

Бренд: Halma Страницы: 2

ALICAT SCIENTIFIC PCD

Бренд: Halma Страницы: 46

Бренд: Harman Страницы: 2

Бренд: T-Link Страницы: 3

Бренд: ICP DAS USA Страницы: 7

I-2533CS Series

Бренд: ICP DAS USA Страницы: 8

Бренд: Safeline Страницы: 8

Бренд: Procom Страницы: 10

Бренд: ShoreStation Страницы: 15

Бренд: LAB-EL Страницы: 25

Бренд: Cardigo Страницы: 12

Q.PEAK DUO XL-G11S.X / BFG Series

Бренд: Qcells Страницы: 26

Бренд: EpiSensor Страницы: 37

Бренд: Potter Страницы: 25

Бренд: A & H Страницы: 35

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды