NuAire NU-5710 Скачать руководство пользователя страница 8

Страница: 8 / 64

OM0249

Page 8 of 64

Rev 4 June/2020

Relative Humidity Control: Available on NU-5720 and NU-5741

Performance Determined with O₂ Set Point @ 21.0%

•

RH Range:

Low is ambient dependent to 95% maximum (default 90%)

(0.0 set point idles the system)

•

RH Accuracy:

+5% / -3%

•

RH Recovery:

90% ±5% : 25 minutes on Average

•

RH Water tank capacity:

3 Liters (approximate)

•

RH Evaporator tank temperature:

Chamber temperature Set point +10⁰ C

control and monitoring system w/ the Fujikura Zirconia sensor Available on the NU-5731 & NU-5741

•

measuring range:

0 to 25 %

•

Default Set-Point:

21% (system is idle at this set point)

•

set- point Range:

.5 to 21% (2 to 21% when RH setpoint is above 90%)

•

Accuracy:

+.25%

•

Recovery

5% +2%: 15 minutes on average

•

Connectors on rear panel are provided for Dry contact remote alarm, RS-485 2way communication,

and 4-20 mA analog output signals for system performance.

Note

: Performance ratings apply ONLY when the Incubator is installed and set up properly per the

instructions in the manual, has stabilized at all set points and is in a stable environment.

See sections 8 and 9 for proper set up.

While idle a system will not inject gas or RH and will not alarm.

3.4

Standard Items Packed With Unit

•

Four (4) stainless steel shelves

•

Eight (8) stainless steel shelf brackets

•

One (1) water pan

(Note: Water pan is included with units having RH Control System for calibration purposes only. See section 9.5.1)

•

Gas supply tube(s)

•

Access port plug - vented

•

One (1), 2 meter (6.5 ft.) electrical cord

10 Amp 18awg with 105⁰C rated jacket *

•

Operation and Maintenance Manual

•

Operating Instructions

*Do not replace

electrical cord with an inadequately rated cord.

A factory supplied replacement is recommended.

3.5

Consult factory for additional Accessories (Ordered Separately)



Содержание NU-5710

































































Результаты поиска

Содержание NU-5710

Отзывы:

Бренды по названию

Популярные бренды

NuAire NU-5710, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание NU-5710

Отзывы:

Бренды по названию

Популярные бренды