NuAire NU-5710 Скачать руководство пользователя страница 25

Страница: 25 / 64

OM0249

Page 25 of 64

Rev 4 June/2020

8.6

Front Component Panel

The front component panel contains the following functions. See BCD-15180

8.6.1

RH Fill Port (Available on models NU-5720 and NU-5741)

The RH evaporator tank is filled through the port that has the red plug (w O-ring) screwed in it. Because of the

pressure in the evaporator tank during an RH injection the O-Ring must seal against the top of the fill port.

8.6.2

Supply filter (Available on models NU-5731 and NU-5741)

The N

supply filter is installed at the factory and should be changed following the instructions found in Maintenance

Section 10.

8.6.3

Supply Filter

The CO

supply filter is installed at the factory and should be changed following the instructions found in

Maintenance Section 10.

8.6.4

Air Inlet Filter - All models

The air inlet filter is installed at the factory and should be changed following the instructions found in Maintenance

Section 10. This is a free air supply.

Note

: DO NOT CONNECT TO A PRESSURIZED SOURCE.

8.6.5

Chamber sample port

The Sample port is provided in the center of the inner glass door for checking the CO

level in the chamber to

monitor the calibration the Sensor and determine if it need adjustment.

8.6.6

Sensor bay access panel

Provides access to the CO2 sensor, Capsule Filter and the Hydrophonic filter for maintenance.

Содержание NU-5710

































































Результаты поиска

Содержание NU-5710

Отзывы:

Бренды по названию

Популярные бренды

NuAire NU-5710, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание NU-5710

Отзывы:

Бренды по названию

Популярные бренды