NuAire NU-5710 Скачать руководство пользователя страница 30

Страница: 30 / 64

OM0249

Page 30 of 64

Rev 4 June/2020

The paragraphs on the following page provide a more complete description of the diagnostics listed above.

The Diagnostic screen is shown to the right of each of the control systems Temperature, CO

, RH & O

and the General

category for your reference. Once entered, the Diagnostics screen will display the calibrated and uncalibrated values of the

given function and all related components.

Temperature Control Diagnostics

Safety Relay

This function shows the current state of the safety relay.

LCD display will show “On” or “Off” corresponding to the

relay condition. On for closed or set or yes.

Chamber Temperature Sensor

This function shows on LCD the current values, calibrated (displayed) and

not calibrated of the temperature sensor controlling the chamber

temperature.

Safety Temperature Sensor

This function shows on LCD the current values, calibrated

and not calibrated of the Safety temperature sensor located in the chamber.

Chamber Heater Triac Control

(0%, 50%, and 100%)

This function allows the jacket heater to be turned on at different percentages 0, 50,100)

Door Heater

This function shows on LCD the current state of the door heater. This function also allows the door heater to be

turned on at different percentages (0, 50, and 100 percent). The LCD display will show phase firing percentage

chosen default is 0%.

Perimeter Heater

This function shows the current state of the perimeter heater. This function also allows the perimeter heater to be

turned on at different percentages (0, 50, and 100 percent). The LCD display will indicate percentage of phase

firing chosen default is 0%.

Control Diagnostics

Sensor

This function shows the current CO

sensor reading both the

“Un-Calibrated sensor signal and the Calibrated value shown in the

display screen.

Inject Valve /

on/

off

This function shows on LCD the current state of the CO

inject valve. LCD

will show “ON” or “OFF” corresponding to the valve condition. On for

open or set or yes.

Sensor Bay Heater Triac Condition /

on/

off

This function shows on LCD the current state of the sensor bay Heater

triac. LCD will show 0, 50, and 100 percent corresponding to the relay

position. The triac can be toggled to each percent of phase firing manually.

Sensor Bay Temperature Sensor

This function shows on LCD the sensor bay temperature in degrees C.

The Sensor bay is heated to temperature set point +3.5 degrees

Air inject Solenoid /

on/

off

This function shows on LCD the current state of the Air Inject Solenoid.

LCD will show “ON” or “OFF” corresponding to the solenoid position.

Default is off-solenoid activates when the button is touched

Air Pump /

on/

off

Содержание NU-5710

































































Результаты поиска

Содержание NU-5710

Отзывы:

Бренды по названию

Популярные бренды

NuAire NU-5710, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание NU-5710

Отзывы:

Бренды по названию

Популярные бренды