NuAire NU-5710 Скачать руководство пользователя страница 56

Страница: 56 / 64

OM0249

Page 56 of 64

Rev 4 June/2020

12.4 On-Board USB Port:

Uploading Service Performance/Event Data:

Refer to STB0348

Uploading Incubator Programming:

Refer to PTB0347

When connecting external accessories or components to the system,

attach only components that have been tested and certified for

compliance to UL/IEC 60601-1 or UL/IEC 60950

13.0 Electrical/Environmental Requirements

13.1 Electrical

Models: NU-5710, NU-5720, NU-5731 and NU-5741

Domestic Units:

115V, 50/60Hz,

1 Phase,

8.5 Amps

“E” Units:

230V, 50/60Hz,

1 Phase,

4.3 Amps

Start Up Power

475 Watts

Running Power

200 Watts

Decon Cycle

750 Watts

13.2 Operational Performance (for indoor use only)

Environment Temperature Range:

F-85

F (15.5

C – 29.4

Environment Humidity:

Maximum relative humidity 80% for temperatures up to

31°C decreasing linearly to 50% relative humidity at 40°C

Environment Altitude:

6562 ft (2000 m) over sea level maximum

13.3 Light Exposure

Standard Fluorescent Lighting @ 150 ft. candles (1614 LUX) maximum intensity.

13.4 Installation Category:

2.0

Installation category (overvoltage category) defines the level of transient overvoltage, which the instrument is designed

to withstand safely. It depends on the nature of the electricity supply and its overvoltage protection means. For

example, in CAT II, which is the category used for instruments in installations supplied from a supply comparable to public

mains such as hospital and research laboratories and most industrial laboratories, the expected transient overvoltage is

2500V for a 230V supply and 1500V for a 120V supply.

13.5 Pollution Degree:

2.0

Pollution degree describes the amount of conductive pollution present in the operating environment. Pollution degree

2.0 assumes that normally only non-conductive pollution such as dust occurs with the exception of occasional

conductivity caused by condensation.

13.6 Chemical Exposure

Chemical exposure should be limited to antibacterial materials used for cleaning and disinfecting. Chlorinated and

Halogen materials are not recommended for use on stainless steel surfaces. Chamber decontamination can be

accomplished by paraformaldehyde, vapor phased Hydrogen Peroxide or Ethylene Oxide without degradation of cabinet

materials.

13.7 EMC Performance (classified for light industrial)

Emissions:

EN61326

Immunity:

EN61326

Class A equipment is intended for use in an industrial environment.

In the documentation for the user, a statement shall be included drawing

attention to the fact that there may be potential difficulties in ensuring

electromagnetic compatibility in other environments, due to conducted

as well as radiated disturbances.

CAUTION

WARNING

Содержание NU-5710

































































Результаты поиска

Содержание NU-5710

Отзывы:

Бренды по названию

Популярные бренды

NuAire NU-5710, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание NU-5710

Отзывы:

Бренды по названию

Популярные бренды