NuAire NU-5710 Скачать руководство пользователя страница 23

Страница: 23 / 64

OM0249

Page 23 of 64

Rev 4 June/2020

8.5

Rear Component Panel Detail

The rear control panel contains the following functions (see also BDC-15170)

8.5.1

Power Cord

The power cord is 6.5-foot (2 m) in length, type “SVT” molded plug, allowing for long life and easy cleaning.

8.5.2

Circuit Breaker

All control electronics are protected with a circuit breaker that may trip at 110% of load rating, but will trip at 145%

of load rating in less than 2 seconds.

Should the circuit breaker open (pop-out button will appear), merely depress to reset.

8.5.3

N2 Inlet on NU-5731 and NU-5741

The N

inlet provides a fitting for vinyl tubing for oxygen control.

Be sure to follow the recommended inlet pressure to insure proper flow rates and consistent O

percentage

readings.

8.5.4

Inlet All models

The CO

inlet provides a fitting for vinyl tubing.

Be sure to follow the recommended inlet pressure to insure proper flow rates and consistent CO

percentage

readings.

8.5.5

Power Switch

The power switch, located at the top of the rear panel, controls all power to the Incubator.

8.5.6

Standard Communication Interface’s / Alarm

Three receptacle connectors are provided for direct field connection of a computer for 2 way communications and

incubator monitoring/or output to a printer or other device only capable of receiving RS-485 digital information,

dry contact remote alarm indicator, also 4 to 20 mA output to an analog monitoring device or system.

All come standard and ready to use. See section 10 for more detail.

8.5.7 Air Inlet

(All Models)

This is a free air supply.

DO NOT CONNECT TO A PRESSURIZED SOURCE.

Air filter is installed at the factory on the front of the unit.

Содержание NU-5710

































































Результаты поиска

Содержание NU-5710

Отзывы:

Бренды по названию

Популярные бренды

NuAire NU-5710, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание NU-5710

Отзывы:

Бренды по названию

Популярные бренды