Novanta f201 Скачать руководство пользователя | Manualshive

Страница: 93 / 105

background image

OTHER LASER FAULTS

PAGE

|

93

•

No voltage is applied to Pin 3 (Remote Interlock) of the User I/O connector.

On systems using remote interlocks, check to see that a positive or negative voltage in the range of ±5–

24 VDC is applied to Pin 3, Remote Interlock, with respect to Pin 11, Input Common, on the User I/O con-

nector (refer to User I/O connections in the Technical Reference chapter for details). For systems not

using interlocks, connect the factory-supplied Quick Start Plug to the User I/O connector on the laser’s

rear panel or wire your male DB-15 connector so that Pin 11 (Input Common) is jumpered to Pin 12 (Auxiliary

DC Power Ground) and Pin 3 (Remote Interlock) is jumpered to Pin 4 (+5 VDC Auxiliary Power).

Symptom:

•

An over-temperature fault is indicated by the following status LEDs and I/O states:

Remote Interlock LED – Green   Interlock Open output – Open
Temp LED – Red       Over Temperature output – Closed
Ready LED – Off             Laser Ready output – Open
Lase LED – Off        Laser Active output – Open

Possible Causes:

•

Coolant temperature is above 28 °C (f201) or there is inadequate coolant flow through the laser.

Check that your chiller is maintaining a water temperature between 18 °C–28 °C (64 °F–82 °F) at a flow

rate of 9.5 lpm (2.5 GPM) for f201.
If water temperature is OK, check the flow rate. The simplest way to do this, if a flow meter is not available,

is to disconnect the cooling tubing from the chiller inlet (or the drain) and run the cooling water for one

minute into a five-gallon bucket; you should have close to the number of gallons listed above. If there is

much less than the recommend flow, check the cooling path for kinked or pinched cooling tubes or check

the chiller for a clogged or dirty filter.

On systems using remote interlocks, check to see that a positive or negative voltage in the range of ±5–

24 VDC is applied to Pin 3, Remote Interlock, with respect to Pin 11, Input Common, on the User I/O con-

nector (refer to User I/O connections in the Technical Reference chapter for details). For systems not

using interlocks, connect the factory-supplied Quick Start Plug to the User I/O connector on the laser’s

rear panel or wire your male DB-15 connector so that Pin 11 (Input Common) is jumpered to Pin 12 (Auxiliary

DC Power Ground) and Pin 3 (Remote Interlock) is jumpered to Pin 4 (+5 VDC Auxiliary Power).

Warning: Serious Personal Injury

On f201 OEM lasers, remote interlock faults are not latched. Clearing the fault condition re-enables

the Ready indicator and the laser will fire after the five-second delay provided that the Shutter

indicator is lit and a PWM Command signal is applied. Because exposure to 10.6

μ

m CO2 laser

radiation can inflict severe corneal injuries and seriously burn human tissue, the OEM or System

Integrator must ensure that appropriate safeguards are in place to prevent unintended lasing.

«
...
91
92
93
94
95
...
»

Содержание f201










































































































Отзывы:

Нет отзывов

Похожие инструкции для f201

BML SL1-ALZ-ZZ Series

Бренд: Balluff Страницы: 26

Бренд: National Instruments Страницы: 15

Бренд: Parkside Страницы: 114

Бренд: LumaSense Страницы: 23

Бренд: Rae Страницы: 38

Бренд: FlowLine Страницы: 2

Бренд: Alpes Lasers Страницы: 41

Бренд: Thermo Scientific Страницы: 56

Бренд: Velleman Страницы: 15

Бренд: FuzzDog Страницы: 6

Бренд: Omega Страницы: 59

Бренд: YOSensi Страницы: 27

Бренд: Scheppach Страницы: 20

Бренд: ScienTECH Страницы: 44

Бренд: Leutert Страницы: 8

xStorage Home Series

Бренд: Eaton Страницы: 16

SEC2000 Spectra System

Бренд: BAS Страницы: 66

Sensus 412 Series

Бренд: Xylem Страницы: 13

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды