Novanta f201 Скачать руководство пользователя

Страница: 43 / 105

COMPLIANCE

PAGE

Remote Interlock

Indicator

Rear panel indicator

(Green/Red)

Illuminates green when

Remote Interlock

circuitry is closed.

Illuminates red when

interlock circuitry is

open.

Over Temperature

Protection

Circuit Element

Temperature shutdown

occurs if temperature

of the laser tube rises

above safe operating

limits

Yes

Temp Indicator

Rear panel indicator

(Green/Red).

Illuminates green when

laser temperature is

within operating limits,

changing to red when

thermal limits are

exceeded.

Warning Labels

f201 exterior

Labels attached to

various external

housing locations.

Warnings to personnel

of potential laser

hazards.

Yes

1 Not available on f201 OEM lasers

When integrating NOVANTA f201 OEM lasers, the Buyer and/or integrator of the end system is responsible

for meeting all applicable Standards to obtain the CE mark. To aid this compliance process, NOVANTA

testing program has demonstrated that f201 lasers comply with the relevant requirements of 2014/30/EU,

the Electromagnetic Compatibility Directive, as summarized in the table below.

Table 3-2 European Union Directives

Applicable Standards/ Norms

2014/30/EU

Electromagnetic Compatibility Directive

2014/35/EU

Low Voltage Directive

2015/863/EU

RoHS Directive

EN 61010-1:2010

Safety Requirements for Electrical Equipment for Measurement, Control, and Laboratory Use - Part 1:

General Requirements

EN 61000-6-4

Radiated Emissions Group 1, Class A

EN 61000-6-4

Conducted Emissions Group 1, Class A

EN 61000-6-2

Electrostatic Discharge Immunity

EN 61000-6-2

RF Electromagnetic Field Immunity

EN 61000-6-2

Electrical Fast Transient/Burst Immunity

EN 61000-6-2

Conducted RF Disturbances Immunity

After a laser or laser processing system has met the requirements of all applicable EU Directives, the

product can bear the official compliance mark of the European Union as a Declaration of Conformity.

Содержание f201










































































































Результаты поиска

Содержание f201

Отзывы:

Похожие инструкции для f201

Бренды по названию

Популярные бренды

Novanta f201, Руководство пользователя

Результаты поиска

Содержание f201

Отзывы:

Похожие инструкции для f201

Бренды по названию

Популярные бренды