Novanta f201 страница 25 Скачать руководство пользователя

Страница: 25 / 105

PS-96 AC INPUT SECTION

PAGE

DC Power cable

To connect the DC Power cable to your f201 laser, refer to the following figure and perform the steps

described below.

DC Power cable—f201 lasers

Verify that input AC voltage to the DC power supply is physically locked out or disconnected.

Locate the f201 DC Power cable. The DC Power cable is 5 meters (16 feet) long with a plug on one

end and five (5) connection lugs on the other. This cable has a minimum bend radius of 87.4 mm

(3.44").

Important Note: Always re-install the terminal guard to protect users against inadvertent contact

with hazardous DC voltages on the connection lugs and DC output terminals.

Carefully remove the plastic terminal guard from the output terminal block.

4 On the lug end of the cable, attach the two black wires with the “0 VDC” marker to the negative

(–) 96 VDC output terminal on the DC power supply. Tighten the terminal nut to a maximum torque

of 4.0 N m (35 in lb.).

PS-96 AC input section

Three-phase operation (recommended)

NOVANTA’s PS-96 DC power supply is capable of supplying 96 VDC at 47 amperes maximum. Three-

phase AC input power requirements for the PS-96 supply are 105–264 VAC, 3Ø (three phase with ground

phase to phase), 23 A maximum per phase, 47–63 Hz. The following table provides recommendations for

three-phase input wiring and fusing.

Caution: Possible Equipment Damage

All AC input wiring and fusing to the DC power supply must be sized and connected in accordance
with applicable local, state, and national requirements.

Local, state, and national code requirements (like NEC, CSA, and IEC 60364) supersede any
recommendations provided in this manual.

Содержание f201










































































































Результаты поиска

Содержание f201

Отзывы:

Похожие инструкции для f201

Бренды по названию

Популярные бренды

Novanta f201, Руководство пользователя

Результаты поиска

Содержание f201

Отзывы:

Похожие инструкции для f201

Бренды по названию

Популярные бренды