Novanta f201 Скачать руководство пользователя страница 20

Страница: 20 / 105

COOLING CONNECTIONS

PAGE

•

Push tubing completely into the fitting, then pull the tubing to verify that it is locked into place.

Tubing extends into the fitting approximately 7/8 of an inch.

•

If tubing must be disconnected from a fitting, first push and hold the tubing slightly into the fitting.

Next push the white fitting ring evenly towards the fitting, and then pull the tubing free.

•

After disconnecting tubing from a fitting, trim 12.7 mm (1/2") from its end before reconnecting.

Trimming the end of the tubing before reconnecting the fitting provides an undisturbed sealing

surface.

Laser cooling fittings

If your integrated laser application uses metric cooling tubing, we recommend the installation of tubing

adaptors to convert the laser’s existing WATER IN/WATER OUT fittings from 1/2-inch standard to 12-

mm metric tubing. The ship kit sent with your f201 laser includes a cooling kit containing two each 1/2-

inch male to 1/2-inch female 90° adaptors and two each 1/2-inch male to 12-mm female 90° adaptors. If

required, many tubing and fitting manufacturers can supply 1/2-inch to 12-mm straight fittings.

Chiller preparation guidelines

•

The ship kit includes chiller fittings with 3/8" NPT male threads. If these fittings will not connect to

your chiller, then you must provide fittings that will adapt the laser’s 1/2" O.D. polyethylene cooling

tubing to your chiller’s Inlet and Outlet ports.

•

Because F201 laser’s cooling tubing is supplied in inch sizes, do not use metric tubing fittings unless

you have installed the appropriate inch-to-metric tubing adaptors. The use of metric fittings on

inch size tubing will lead to coolant leaks or may allow the pressurized tubing to blow off the fitting.

Coolants

NOVANTA recommends the laser’s cooling fluid contain at least 90% distilled water by volume. In closed-

loop systems, use a corrosion inhibitor/algaecide such as Optishield

Plus or equivalent as required. Avoid

glycol-based additives because they reduce the coolant’s heat capacity and high concentrations may

affect power stability. For NOVANTA lasers, the minimum coolant setpoint is 18 °C (64 °F) so glycol is not

necessary unless the chiller is subjected to freezing temperatures. If tap water is used, chloride levels

should not exceed a concentration of 25 parts per million (PPM) and total hardness should be below 100

PPM. Install a filter on the chiller’s return line and inspect frequently. f201 lasers use the following wetted

materials in the coolant path—aluminum, brass, copper, Delrin

, PBT, polyethylene, stainless steel, and

Viton

Caution: Possible Equipment Damage

f201 lasers incorporate special fittings that accept only standard 1/2" O.D. cooling tubing.

DO NOT REMOVE OR ADJUST THESE FITTINGS!

Each laser is shipped with a cooling kit that includes 90° push-on tubing connectors to adapt the
brass fittings to your choice of standard (1/2-inch) or metric (12-mm) cooling tubing.

Содержание f201










































































































Результаты поиска

Содержание f201

Отзывы:

Бренды по названию

Популярные бренды

Novanta f201, Руководство пользователя

Результаты поиска

Содержание f201

Отзывы:

Бренды по названию

Популярные бренды