Novanta f201 Скачать руководство пользователя

Страница: 21 / 105

COOLING CONNECTIONS

PAGE

Important Note: DO NOT use de-ionized (DI) water as a coolant. DI water is unusually corrosive

and is not recommended for mixed material cooling systems.

Setting coolant temperature

Choosing the correct coolant temperature is important to the proper operation and longevity of your laser.

When coolant temperature is lower than the dew point (the temperature at which moisture condenses out

of the surrounding air), condensation forms inside the laser housing leading to failure of laser electronics

as well as damage to optical surfaces.
The greatest risk of condensation damage occurs when the laser is in a high heat/high humidity environ-

ment and the chiller’s coolant temperature is colder than the dew point of the surrounding air or when the

system is shut down, but coolant continues to flow through the laser for extended periods of time.
The chiller’s temperature setpoint must always be set above the dew point temperature. In cases where

this is not possible within the specified coolant temperature range of 18 °C to 22 °C (64 °F to 72 °F), then

the following steps MUST be taken to reduce the risk of condensation damage.

•

Use the Gas Purge port (f201) to introduce nitrogen or dry, filtered air into the laser housing.

•

Air-condition or dehumidify the room or the enclosure containing the laser.

•

Increase coolant flow by an additional 3.8 lpm (1.0 GPM). Do not exceed a coolant pressure of 414

kPa (60 PSI).

Important Note: To reduce problems associated with condensation, F201 laser f201asers can

operate up to 28 °C. However, these elevated cooling temperatures may result in decreased laser

performance and/ or reduced laser lifetime.

Содержание f201










































































































Результаты поиска

Содержание f201

Отзывы:

Похожие инструкции для f201

Бренды по названию

Популярные бренды

Novanta f201, Руководство пользователя

Результаты поиска

Содержание f201

Отзывы:

Похожие инструкции для f201

Бренды по названию

Популярные бренды