Novanta f201 Скачать руководство пользователя страница 17

Страница: 17 / 105

MOUNTING

PAGE

Mounting

f201 mounting

F201 mounting brackets are threaded to accept either metric or standard fasteners.

Important Note: As shown in the figure below, DO NOT use more than one fastener per

mounting location. Using two or more fasteners per mounting tab will cause damage to the laser;

use only one fastener per location to mount your f201 laser.

Fastening f201 lasers from above

To fasten your f201 laser to a mounting surface from above, perform the following steps:

Refer to the appropriate outline and mounting drawing for dimensions and then drill and tap three

mounting holes into your mounting surface. For SAE installations, drill and tap three 5/16–18 (f201).

Assemble three spherical washer sets as detailed in the Outline and Mounting drawing.

Place the spherical washer sets over the threaded holes in your mounting surface.

Carefully position the laser so that each thru hole in the baseplate aligns with a spherical washer

and threaded mounting hole.

Insert the appropriate metric or standard cap screws, included in the laser’s ship kit, through the

baseplate, through the spherical washers, and into the threaded holes of the mounting surface (see

figure below). Turn the screws by hand until the threads engage.

Evenly tighten all three cap screws. For M8 cap screws, torque to 12 N m; for M10 screws, torque

to 24 N m. When using 5/16" screws, torque to 13 ft lb.; for 3/8" cap screws, tighten to 23 ft lb.

Caution: Possible Equipment Damage

Do not use more than one fastener per mounting foot. Doing so will damage the laser.

Содержание f201










































































































Результаты поиска

Содержание f201

Отзывы:

Бренды по названию

Популярные бренды

Novanta f201, Руководство пользователя

Результаты поиска

Содержание f201

Отзывы:

Бренды по названию

Популярные бренды