Novanta f201 Скачать руководство пользователя

Страница: 79 / 105

MAINTENANCE AND TROUBLESHOOTING

PAGE

Maintenance and troubleshooting

Use information in this section to perform maintenance or troubleshoot your f201 laser.

This section contains the following information:

•

Maintenance – describes typical f201 maintenance procedures.

•

Troubleshooting – explains how to troubleshoot common f201 problems.

Disabling f201 lasers

Before performing any maintenance on your f201 laser, be sure to completely disable the laser by

disconnecting the DC Power cable (or cables) from the rear of the laser.

Daily inspections

Perform the following steps daily to keep your f201 laser in optimum operating condition. Except for the

procedures described below, no other service is required or should be attempted.

Inspect all cooling tubing connections for signs of leakage. Check for signs of condensation that

may indicate the cooling water temperature has been set below the dew point temperature.

Condensation will damage electrical and optical components inside the laser. See Setting coolant

temperature in the Getting Started chapter for details on preventing condensation.

When using compressed air as a purge gas on your f201 laser, empty water traps and oil separa-

tors on each filter and/or dryer between the laser and your compressed air source. Compressed

air purity must meet the purge gas specifications shown in Table 1-6 in the Getting Started

chapter.

Caution: Possible Equipment Damage

If you operate your laser or marking head in a dirty or dusty environment, contact NOVANTA about
the risks of doing so and precautions you can take to increase the longevity of your laser, marking
head, and associated optical components.

Warning: Serious Personal Injury

A risk of exposure to toxic elements, like zinc selenide, may result when certain optical or beam

delivery components are damaged. In the event of damage to laser, marking head, or beam delivery

optics, contact NOVANTA, Inc. or the optics manufacturer for handling instructions.

Содержание f201










































































































Результаты поиска

Содержание f201

Отзывы:

Похожие инструкции для f201

Бренды по названию

Популярные бренды

Novanta f201, Руководство пользователя

Результаты поиска

Содержание f201

Отзывы:

Похожие инструкции для f201

Бренды по названию

Популярные бренды