Novanta f201 Скачать руководство пользователя страница 49

Страница: 49 / 105

INITIAL START-UP

PAGE

Initial start-up

The Initial start-up section includes subsections:

•

With a UC-2000 Controller

•

Without a UC-2000 Controller

With a UC-2000 Controller

Before your laser is put into service for the first time, its functionality should be verified. Follow this

procedure to verify the laser system is operating at optimum performance. For this procedure, use the

UC-2000 as a stand-alone controller; do not attempt to control the laser or UC-2000 externally.
Note: When performing the initial start-up sequence, you must first connect the Quick Start Plug or you

must provide the required Remote Interlock and Shutter Open Request signals to the User I/O connector.

See User I/O connections in the Technical Reference chapter for User I/O pinouts and signal descriptions.

Starting auxiliary equipment

Ensure that all personnel in the area are wearing protective eyewear.

Remove the red self-adhesive aperture seal from the laser faceplate.

Place a beam block 61 cm (24 in) from the laser aperture to prevent the beam from traveling

beyond the work area.

Turn on the chiller and set the temperature setpoint between 18 °C–22 °C. Verify that the chiller is

delivering the recommended flow rate for your laser at less than 414 kPa (60 PSI) of pressure.

Examine all cooling connections carefully and ensure that they do not leak.

Start purge gas flow at a rate of 0.85–1.7 m

/hr (30–60 SCFH, Standard Cubic Feet per Hour) at a

pressure not to exceed 34.5 kPa (5 PSI). If a flowmeter is not available, set a purge pressure

between 13.8–34.5 kPa (2–5 PSI).

Important Note:

If you have not yet operated your UC-2000 Universal Laser Controller, refer to

the UC-2000 Laser Controller Operator’s Manual and quick start guide for setup and operation

instructions before continuing.

Set the UC-2000 to MANUAL mode, and then set the PWM Adj Knob to provide zero percent

output (0.0%). The UC-2000’s Lase indicator should be Off.

Verify that the laser’s Keyswitch (if equipped) is in the OFF/RESET position.

Turn on the +96 VDC power supply.

If the factory-wired Quick Start Plug is installed, the Remote Interlock indicator will illuminate green and

the Shutter indicator will illuminate blue—if the manual Shutter Switch is Open. The Temp indicator will

illuminate green if laser temperature is within safe operating limits.

Содержание f201










































































































Результаты поиска

Содержание f201

Отзывы:

Бренды по названию

Популярные бренды

Novanta f201, Руководство пользователя

Результаты поиска

Содержание f201

Отзывы:

Бренды по названию

Популярные бренды