Nortel Passport 5430 Скачать руководство пользователя страница 96

Страница: 96 / 220

Installing and Operating the Passport 5430 Multiservice Access Switch

4-18

306308-A Rev 00

Figure 4-12.

Using the Cable Looms

To use the cable looms:

Make sure that the cable looms are installed as described in “Installing
the Passport 5430” on page 1-5.

Using the guidelines above, determine which card to cable first.

If you are cabling a port on a PCI card, begin with the Module 1 port.

Insert the cable into the cable loom slot corresponding to the card
containing the module you are cabling.

Allowing some slack in the cable between the cable loom and the module
connector, insert the cable into the module connector.

For cabling instructions, see

“Connecting Communications Cables

” on

page 4-1

, and

“Connecting a Management Console

” on

page 4-7

Remove excess cable slack by slowly pulling the cable through the cable
loom away from the connector.

To ease card removal, the cable should curve naturally and not drape over
other cards and modules. Make sure that cables can be quickly reconnected to
the appropriate connector.

FBR0110A

Cable loom

5V FLASH ONL

PCMCIA 2

Port 2

Port 1

Port 2

Port 1

Insert

Extract

PCMCIA 1

SYNC

LOOP

RED
ALM

TX/RX

SPD

Link

PS1

PS2

Fan

WAN

S-PMC

cPCI

Run

Boot

Base

YEL
ALM

PMC

Module2

Module1

ENET-1

ENET-2

Console

System

Processor

Expansion Module

Insert

Extract

Expansion Module

T1/E1

Dsync

Port 2

Port 1

Module1

Dsync

Port 2

Port 1

Dsync

Telco

RLSD

DTR

V.34 Modem

RLSD

ISDN BRI

withNT1

PCI Slot 1

PCI Slot 2

PCI Slot 3

PCI Slot 4

Содержание Passport 5430





























































































































































































































Результаты поиска

Содержание Passport 5430

Отзывы:

Nortel Passport 5430, Инструкции по установке и эксплуатации, Страница: 96 / 220

Результаты поиска

Содержание Passport 5430

Отзывы: