manualshive.com logo in svg

Nortel Passport 5430, Инструкции по установке и эксплуатации, Страница: 73 / 220

Поделиться
Скачать
Nortel Passport 5430 Скачать руководство пользователя страница 73

Accessing the Interior

306308-A Rev 00

3-7

Installing a PMC Module Filler Panel

If you plan to remove a PMC module from the Passport 5430 without immediately 
replacing it, you must install a PMC module filler panel in the slot.

To install a PMC module filler panel:

1.

Locate the slot where you want to install the PMC module filler panel.

2.

Insert the filler panel in the PMC module slot 

(Figure 3-4)

.

Removing and Installing a WAN Adapter Module Filler Panel

Nortel Networks ships the Passport 5430 with a filler panel in each empty WAN 
adapter module card slot. 

Before you can install a new WAN adapter module, you must remove the 
appropriate WAN adapter module filler panel. For instructions, see the next 
section, “

Removing a WAN Adapter Module Filler Panel

.” 

If you need to install a WAN adapter module filler panel, see “

Installing a WAN 

Adapter Module Filler Panel

” on 

page 3-9

.

Removing a WAN Adapter Module Filler Panel 

To remove the filler panel from an empty WAN adapter module slot:

1.

Using a Phillips screwdriver, remove the screw that secures the filler 
panel 

(Figure 3-5)

. 

Содержание Passport 5430





























































































































































































































Отзывы:

Нет отзывов