Nord Drivesystems NORDAC LINK SK250E-FDS, Руководство пользователя

Страница: 173 / 212

6 Operating status messages
BU 0250 en-3021 173
Pos: 606 /Anleitungen/Elektronik/FU und Starter/6. Meldungen zum Betriebszustand/Meldungen Einschaltsperre (Tabellenüberschrift) @ 3\mod_1361803467385_388.docx @ 59922 @ 5 @ 1
Switch-on block messages
Display in the
SimpleBox /
ControlBox
Reason:
Text in the ParameterBox
Cause
• Remedy
Group Details in
P700 [-03]
Pos: 607 /Anleitungen/Elektronik/FU und Starter/6. Meldungen zum Betriebszustand/Störmeldungen (Auflistung)/Information I000_01 [SK 180E ... SK 5xxE/SK 500P] @ 2\mod_1347457775195_388.docx @ 47347 @ @ 1
I000 0.1 Disable voltage from IO If the function "disable voltage"is parameterised, input (P420
/ P480) is at Low
•
Set "input High"
•
Check signal cable (broken cable)
0.2 IO fast stop If the function "fast stop"is parameterised, input (P420 /
P480) is at Low
• Set "input High"
• Check signal cable (broken cable)
0.3 Block voltage from bus
•
For bus operation (P509):
control word Bit 1 is
"Low"
0.4 Bus fast stop • For bus operation (P509):
control word Bit 2 is
"Low"
0.5 Enable on start Enable signal (control word, Dig I/O or Bus I/O) was already
applied during the initialisation phase (after mains "ON", or
control voltage "ON"). Or electrical phase is missing.
•
Only issue enable signal after completion of
initialisation (i.e. when the FI is ready)
•
Activation of "Automatic Start" (P428)
0.6 – 0.7 Reserved
Information message for PLC

see supplementary
instructions
Pos: 608 /Anleitungen/Elektronik/FU und Starter/6. Meldungen zum Betriebszustand/Störmeldungen (Auflistung)/Information I000_02-Ergänzung 08 und 09 [SK 180E ... SK 5xxE/SK 500P] @ 10\mod_1455725649528_388.docx @ 306332 @ @ 1
0.8 Right direction blocked Switch-on block with inverter shut-off activated by:
P540 or by "Enable right block" (P420 = 31, 73) or "Enable
left block" ( P420 = 32, 74),
The frequency inverter switches to "Ready for switching on"
status
0.9 Left direction blocked
Pos: 609 /Anleitungen/Elektronik/FU und Starter/6. Meldungen zum Betriebszustand/Störmeldungen (Auflistung)/Information I006 [SK 180E ... SK 5xxE, außer SK 500P] @ 2\mod_1347457929759_388.docx @ 47372 @ @ 1
I006
1)
6.0 Charging error Charging relay not energised, because:
•
Mains / link voltage too low
•
Mains failure
•
Evacuation run activated ((P420) / (P480))
Pos: 610 /Anleitungen/Elektronik/FU und Starter/6. Meldungen zum Betriebszustand/Störmeldungen (Auflistung)/Information I011 [SK 180E ... SK 5xxE/SK 500P] @ 2\mod_1347457936856_388.docx @ 47397 @ @ 1
I011 11.0 Analog Stop If an analog input of the frequency inverter or a connected
IO extension is configured to detect cable breaks (2-10V
signal or 4-20mA signal), the frequency inverter switches to
the status "ready for switch-on" if the analog signal
undershoots the value
1 V or 2 mA
This also occurs if the relevant analog input is
parameterised to function "0" ("no function").
• Check connections
Pos: 611 /Anleitungen/Elektronik/FU und Starter/6. Meldungen zum Betriebszustand/Störmeldungen (Auflistung)/Information I014 "reserviert" [SK 200E ... SK 5xxE/ SK 500P] @ 2\mod_1347457944329_388.docx @ 47422 @ @ 1
I014
1)
14.4 Reserved Error message for POSICON

see supplementary
instructions
Pos: 612 /Anleitungen/Elektronik/FU und Starter/6. Meldungen zum Betriebszustand/Störmeldungen (Auflistung)/Information I018 "reserviert" [SK 2xxE/ SK 5xxE/ SK 2xxE-FDS/SK 500P] @ 2\mod_1347457946544_388.docx @ 47447 @ @ 1
I018
1)
18.0 Reserved Information message for "Safe Stop" function

see
supplementary instructions
Pos: 613 /Anleitungen/Elektronik/FU und Starter/6. Meldungen zum Betriebszustand/Störmeldungen (Auflistung)/Information - Kennzeichnung "Nicht bereit" @ 20\mod_1513067472948_388.docx @ 2375129 @ @ 1
1) Indication of operating mode (message) on the
ParameterBox
or virtual operating unit of the NORD CON-
Software
: "Not ready"
Pos: 614 /Allgemein/Allgemeingültige Module/---------Seitenumbruch kompakt --------- @ 13\mod_1476369695906_0.docx @ 2265495 @ @ 1