Nikon NPL-302 Series Скачать руководство пользователя | Manualshive

Страница: 9 / 234

background image

Safety

Pulse Laser Station NPL-302 Series Instruction Manual

ix

C

Warning –

Use only the specified battery charger (part number Q-75U/E) to

charge the battery pack (part number BC-65). Using other chargers, such as
a charger with part number Q-7U/E or Q-7C, may cause the battery pack to
catch fire or rupture. (The BC-65 cannot be charged by the Q-7U/E or Q-7C.)

C

Warning –

Do not cover the battery charger while the battery pack is being

recharged. The charger must be able to dissipate heat adequately. Coverings
such as blankets or clothing can cause the charger to overheat.

C

Warning –

Avoid recharging the battery pack in humid or dusty places, in

direct sunlight, or near heat sources. Do not recharge the battery pack when it
is wet. If you do, you may receive electric shocks or burns, or the battery pack
may overheat or catch fire.

C

Warning –

Although the battery pack (part number BC-65) has an auto-reset

circuit breaker, you should take care not to short circuit the contacts. Short
circuits can cause the battery pack to catch fire or burn you.

C

Warning –

Never burn or heat the battery. Doing so may cause the battery to

leak or rupture. A leaking or ruptured battery can cause serious injury.

C

Warning –

Before storing the battery pack or battery charger, cover the

contact points with insulation tape. If you do not cover the contact points, the
battery pack or charger may short circuit, causing fire, burns, or damage to
the instrument.

C

Warning –

The battery BC-65 is not waterproof on its own. Do not get the

battery wet when it is removed from the instrument. If water seeps into the
battery, it may cause a fire or burns.

«
...
7
8
9
10
11
...
»

Содержание NPL-302 Series











































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для NPL-302 Series

Бренд: AccuMASTER Страницы: 2

Бренд: Bante Instruments Страницы: 6

Бренд: Taber Страницы: 53

Бренд: National Instruments Страницы: 85

Бренд: National Instruments Страницы: 12

Бренд: National Instruments Страницы: 18

Бренд: National Instruments Страницы: 12

Бренд: Oldham Страницы: 34

Бренд: VEE GEE Страницы: 2

Бренд: FMS Страницы: 12

KINGFISHER PLUS+

Бренд: semaphore Страницы: 247

Бренд: Saluki Technology Страницы: 161

Бренд: A&D Страницы: 24

Бренд: Hanna Instruments Страницы: 12

Бренд: T&D Страницы: 31

Sonic-Pro S6A Series

Бренд: Blue-White industries Страницы: 2

Бренд: FMT Swiss AG Страницы: 24

Бренд: Carman Страницы: 64

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды