Nikon NPL-302 Series Скачать руководство пользователя

Страница: 178 / 234

Menu Key

158

Pulse Laser Station NPL-302 Series Instruction Manual

The point name is added to the current layer and
the list is updated.

Adding a code

In the code list, press the

Add

softkey to add a

new feature code to the current layer.

Enter the feature code in the CD field. Press

[MODE]

to change between alphabetic and numeric

input mode.

You can use the REC field to define a numeric
identifier for each feature code. This is optional: If
there is a value in the REC field, this value is
stored. If you leave the REC field blank, the CD
value is stored.

Press

[ENT]

to add the new code and update the

code list

Содержание NPL-302 Series











































































































































































































































Результаты поиска

Содержание NPL-302 Series

Отзывы:

Похожие инструкции для NPL-302 Series

Бренды по названию

Популярные бренды

Nikon NPL-302 Series, Инструкция по эксплуатации

Результаты поиска

Содержание NPL-302 Series

Отзывы:

Похожие инструкции для NPL-302 Series

Бренды по названию

Популярные бренды