Nikon NPL-302 Series Скачать руководство пользователя

Страница: 173 / 234

Menu Key

Pulse Laser Station NPL-302 Series Instruction Manual

153

You can use the asterisk (*) as a wildcard. For
example, when you enter

500*

in the PT field,

the search matches the points named 500, 500-1,
500-A, and 5000.

If more than one point matches the search criteria,
the matching points are displayed in a list.

Use

[^]

[v]

to highlight the point you want to use.

Press

[ENT]

to select it.

Detailed data for the selected record appears.
Press the

DSP

softkey to change the fields shown.

Press

[ESC]

to return to the list.

To search by point type, move to the Type field
and use

[<]

[>]

to change the selected point

type. The options are ALL, MP, UP, CC, and RE.

If no point matches the specified criteria, an error
screen appears. Press any key to return to the
data screen.

Содержание NPL-302 Series











































































































































































































































Результаты поиска

Содержание NPL-302 Series

Отзывы:

Похожие инструкции для NPL-302 Series

Бренды по названию

Популярные бренды

Nikon NPL-302 Series, Инструкция по эксплуатации

Результаты поиска

Содержание NPL-302 Series

Отзывы:

Похожие инструкции для NPL-302 Series

Бренды по названию

Популярные бренды