Nikon NPL-302 Series Скачать руководство пользователя

Страница: 170 / 234

Menu Key

150

Pulse Laser Station NPL-302 Series Instruction Manual

Use

[^]

[v]

to highlight a field. Then modify

the value in the selected field.

To finish editing, press

[ENT]

in the CD field.

A confirmation screen appears.

Do one of the following:

–

To accept the changes and return to the
data view screen, press

[ENT]

or the

Yes

softkey.

–

To go back to the edit screen, press

[ESC]

the

softkey.

Editing station records

Note –

The system will not recalculate measurements if you change the station

record. All coordinate and raw data observed from an edited station record must be
recalculated in your postprocessing software.

In the RAW screen, use

[^]

[v]

to highlight the

station record that you want to edit. Then press the

Edit

softkey.

You can edit any field in the ST record, but the
instrument does not recalculate any measurements
from this station.

Press

[ENT]

in the AZ field to confirm the change.

Содержание NPL-302 Series











































































































































































































































Результаты поиска

Содержание NPL-302 Series

Отзывы:

Похожие инструкции для NPL-302 Series

Бренды по названию

Популярные бренды

Nikon NPL-302 Series, Инструкция по эксплуатации

Результаты поиска

Содержание NPL-302 Series

Отзывы:

Похожие инструкции для NPL-302 Series

Бренды по названию

Популярные бренды