Nikon NPL-302 Series Скачать руководство пользователя

Страница: 112 / 234

Applications

Pulse Laser Station NPL-302 Series Instruction Manual

To store the point and its offset distance
information, press

[ENT]

Enter the point name and feature code.

You can also use this screen to change the HT
value.

Sample records

CO, 2pt-Ref Pt:16 & Pt:13 Az:311.2932
CO, Sta= -12.6876 Offset= 1.3721 dZ= 0.0971
SS,17,1.0000,6.9202,18.4700,80.3120,15:48:48,2REF-LINE

Measuring distance and offset values on the arc-curve

40.1

Press

[2]

or select

Arc RefLine

in the

Programs menu.

Enter the start of the curve point (P1) and the
azimuth of its tangent line (AZ1).

To enter P1 by direct measurement, press the

MSR

softkey.

Choose a method to define the arc.

P2 can be any point on the tangent line that is
to exit the curve.

Содержание NPL-302 Series











































































































































































































































Результаты поиска

Содержание NPL-302 Series

Отзывы:

Похожие инструкции для NPL-302 Series

Бренды по названию

Популярные бренды

Nikon NPL-302 Series, Инструкция по эксплуатации

Результаты поиска

Содержание NPL-302 Series

Отзывы:

Похожие инструкции для NPL-302 Series

Бренды по названию

Популярные бренды