Nikon NPL-302 Series Скачать руководство пользователя

Страница: 171 / 234

Menu Key

Pulse Laser Station NPL-302 Series Instruction Manual

151

Searching records

50.1

You can search for records by their type, point name, code, or by any combination
of these values.

Searching raw records

In the RAW screen, press the

Srch

softkey to

access the raw data search function.

To find a point by name, enter the name in the PT
field and press

[ENT]

twice.

You can use the asterisk (*) as a wildcard. For
example, when you enter

30*

in the PT field, the

search matches the points named 300, 301, 302,
3000A2, and 3010.

If you change the ST or HI values, the coordinates of observation points are not
recalculated. A comment record is stored to record the change. The following
example shows a comment record for a changed HI value:

CO,HI changed at ST:9012 Old HI= 1.345m

If you change the BS or AZ values, raw records are not recalculated. A comment
record is stored to record the change.

To search by point type, move to the Type field
and use

[<]

[>]

to change the selected point

type. The options are ALL, ST, SS, SO, CP, CO,
CO(SY), and CO(RDM).

Содержание NPL-302 Series











































































































































































































































Результаты поиска

Содержание NPL-302 Series

Отзывы:

Похожие инструкции для NPL-302 Series

Бренды по названию

Популярные бренды

Nikon NPL-302 Series, Инструкция по эксплуатации

Результаты поиска

Содержание NPL-302 Series

Отзывы:

Похожие инструкции для NPL-302 Series

Бренды по названию

Популярные бренды