Nikon NPL-302 Series Скачать руководство пользователя | Manualshive

Страница: 50 / 234

background image

3

Getting Started

30

Pulse Laser Station NPL-302 Series Instruction Manual

Selecting a Language

3.1

The Nikon total station supports one Language Pack at a time. The Language Pack
is a set of up to three different languages installed on the instrument from which the
user can select. Several Language Packs are available for the Nikon total stations.

• Language Pack #1: English, French, Spanish

• Language Pack #2: English, German, Italian

• Language Pack #3: English, Chinese, Russian

1.

To select a different language, power on
the instrument and press

[ESC]

and

[3]

at the

Tilt Telescope screen.

The

Select Language

screen appears. Up to

three languages are available in the
installed Language Pack. The screen shows
which languages are currently available on
the instrument.

The current language selection is highlighted.

2.

Press

[^]

or

[v]

to highlight the required

language and then press

[ENT.]

3.

The instrument reboots and displays the
start-up

Tilt Telescope

screen in the

selected language.

Language Pack #1 is the default Language Pack installed at the factory. Other
Language Packs can be installed at an authorized Nikon total station service
provider.

«
...
48
49
50
51
52
...
»

Содержание NPL-302 Series











































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для NPL-302 Series

Бренд: Campbell Страницы: 25

Бренд: Larson Davis Страницы: 2

Бренд: G-Tek Страницы: 27

Бренд: National Instruments Страницы: 85

Бренд: National Instruments Страницы: 12

Бренд: National Instruments Страницы: 18

Бренд: National Instruments Страницы: 12

Бренд: OHAUS Страницы: 32

Бренд: Magnet-physik Страницы: 32

Бренд: Macnaught Страницы: 8

Бренд: Hanna Instruments Страницы: 16

Бренд: Omega Страницы: 22

C100L-L-DD-LE-5-OV1-SV1-PV1C-V1-S1

Бренд: Sierra Страницы: 55

Бренд: Kawai Страницы: 28

Бренд: THORLABS Страницы: 63

Бренд: Pilot Communications Страницы: 34

Pianovelle GRP3

Бренд: Baldwin Страницы: 34

Бренд: M-system Страницы: 5

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды