Nikon NPL-302 Series Скачать руководство пользователя | Manualshive

Страница: 89 / 234

background image

Applications

4

Pulse Laser Station NPL-302 Series Instruction Manual

69

5.

To record the station, press

[ENT]

.

6.

To finish the station setup after taking a
distance measurement, press

[ENT]

. ST and F1

records are stored to the current job.

Advanced feature: Measuring F1 and F2

To take an angle shot and proceed to the next
measurement on Face-2, press the

F2

softkey.

To go directly to the Face-2 measurement after
taking a distance measurement to the BS on
Face-1, flip the telescope. The instrument
automatically detects F1/F2.

Press

[ENT]

on Face-2. The delta screen appears.

To record a CP record which stores the averaged
HA, VA, and SD from the F1/F2 data, press the

CP

softkey. To record only the ST and F1/F2

records, without a CP record, press the

OK

softkey.

F1/F2 measurements are not available with the NPL-332

«
...
87
88
89
90
91
...
»

Содержание NPL-302 Series











































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для NPL-302 Series

Бренд: Teac Страницы: 148

Бренд: IFM Страницы: 25

Бренд: Campbell Страницы: 16

Goldmann AT 870

Бренд: Haag-Streit Страницы: 20

Бренд: Idexx Страницы: 6

Бренд: IDEAL INDUSTRIES Страницы: 10

Бренд: M-system Страницы: 5

Бренд: jenway Страницы: 50

Бренд: jenway Страницы: 62

BLITZFIRE Series

Бренд: Task Force Tips Страницы: 20

CP-4900 Micro-GC

Бренд: Varian Страницы: 13

Бренд: Artesia Страницы: 36

Бренд: Endress+Hauser Страницы: 88

Бренд: SKF Страницы: 12

Бренд: H. HERMANN EHLERS Страницы: 40

Micropilot S FMR533

Бренд: E+H Страницы: 12

Бренд: National Instruments Страницы: 169

Бренд: International Light Technologies Страницы: 19

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды